Concerning
Foot
Controllers
Explains
the
function
of
foot
controller
They lunclion as explained
in
the following.
1.
Differences
between
FC-100
and
Fe-
100
MKII
With the GP-16, either
the
FC-1
00
or FC-100 MKli
can
be connected and used,
but
there are functional dilfer-
ences depending on the model. Referto the chart below
for
such
differences.
Function
When
selecting
a patch
tromthe
GP-16
panel.
Operating
by the
Expression
pedal.
FC-100
No change
in
the
FC-1
00
display
nevertheless the
GP-16 display
shows newly
selected patch
(One pedal avail-
able:
EXP)
Changes
the
values
01
a
speci~
lied parameter
01
each patch.
,
FC-100MKII
I
Both displays
I
show
the
same
patch (newly
i
selected
one).
,
(Two pedals
available:
EXP1
,
EXP2)
EXP1
: Changes
the values
01
a
specified pa-
rameter
ot
each
patch.
EXP2: Changes
Master Volume
exclusively.
2.
Settings
related
to
the
foot
controller
The requrred settings vary depending
on
the type
01
controllerconnecled. Settings should
be
made
as
shown
below when connecting
10
the GP-16
«When
connecting
the
FC-100»
Mode Seleclion Switch
MODEl
«When
connecting
the FC-100MKII »
Mode
Mode Selection Switch
RRC
Foot
Pedal Mode
MODEl
For information on how the mode
is
set, refer to the
Toot
controller's owner's manual.
3.
Foot
controller
functions
Through connecting
an
FC-100 or FC-100MKII
foot
controller
to
the GP-16, not only will
you
be
able
to
change palches using your foot. but
you
also
can
have
control over a variety of other lunctions convenienl
during actual perlormance.
a.
Use
of
the
Control
pedal
Ordinarify
it
is
used
as
a mute pedal.
When the foot controller's
Control pedal
is
depressed,
and
while
the
control
indicator
is
lit,
no
signals
are
output
trom either the output (phone)
Jacks,
or balanced
(XLR)
connectors
on
the GP-16.
When
not
playing, you can use this pedal
to
prevenl
noise when changing guitars,
or
to
silence mistakes.
Either press the Control pedal again
when
tuning using
Ihe tuner-use Signal Oul, or use the pedal lor selecting
a patch;
it
wililhen
be
released.
Through a change
in
settings.
i1
can also be
set
\0
BY·
PASS.
For information on how 10 make setting changes,
sse
~10.
Set1ing the Function
of
the Control
P8dar~
(IS"'
P.53).
h.
Use
01
the
expression
pedal
Through connection
of
an
expression pedal (EV-5; op-
tional), the values tor a specified parameler
can
be
changed during pertonmance
by
pressing the pedal
connected
10
EXP
(1),
First, tor each palch, specify the parameler which
you
wish to control using the pedaL Then sel the range
01
change
by
setling the maximum value (value when
pedal
is
lully depressed) and the minimum value (when
pedal
is
released). The parameters which
are
available
lor use
in
this way are all those included
in
the effect
on
state, and master volume.
15
1
RBI
To Next Page
Loading...
Need help?
General
