5
IIIIIIIIIII
"BANK"
Sc.LECT
BHr·H:::
i3F'-H
E:k-l
r'~E-:+:
(Example: To transmrt Group
A,
Bank: 1 , Number:
1-B)
"GROUP"
I
i ':;;::1
:=c·""
r'p'nl
jP
_ ............
_·1
.J
'
__
'
! GP-A
8K-*
N8-*
(Example: To transmit Group
A,
Bank:
1-B,
Number: 1-B)
For infonmation on how
to
select Groups (Banks,
Numbers) see
'HJPatch
Selection"
IIG<'
P,12),
When
all Banks (numbers) are included, a
''*''
will be
displayed
at
that position,
«
When
"ALL"
'has
been
selected
in
[Step
4-5]
»
The following will appear in the display.
and
the charac'
ters on the lower line will be blinking,
"ALL"
----,--'~
i~LL
D~T~
DUMP
.
'=',<,,.,
IIPTTE
","'~
1 I
j'
.,
__
I.
'..
, _ _
_~--'
(When transmitling Ihe data tor all patches.)
«
When
"TEMP"
has
been
selected in
[Step
4-5]
»
The following will appear
In
the display. and the charac'
ters on the lower line
will be blinking,
"TEMP"
.--~'----'--
! T
~
j'1
F'
0
F.:
H
F:
'",'
[)
U
1'1
F'
IPu~.h
klF.:ITE:
Ve'=
"._-'-'---
[Step 7,5] Press _WRITE' and Ihe data will
be
transmitted.
50
«
When
"NUMBER",
"BANK"
or
"GROUP"
has
been
selected
in
[Step
4-5]
»
1
(Example:TotransmltGroupA.
Bank:1, Number:
1-B)
«
When
"ALL"
has
been
selected
in
[Step
4-5]
»
Once transmission
of
the
data
has completed. the follow,
ing display will appear, and you return to the state before
the
bulk dump was executed (System mode).
I 5HI,.! I
[,113
I
,-.
n
1-'1'""'
I ;:: T
C"
;-'r
I j
11_._1
r
........
,
'-
...
[Step 8-5] When the transfer has completed. press
I ESCAPE I
and
return
to
the Play mode.
6.
Data Reception
and
Verification
(Bulk
load,
Verify)
Through employing Roland Exclusive messages,
you
can receive (Bulk Load) the patch data
tromanotherGP,
16 or a sequencer. In addition, the unit
IS
equipped with
a
Verify lunction
so
you can check
if
the data has been
correctly transferred.
<
Concerning
Verify
>
The
GP'16,
In
addition to the conventional bulk dump
and
bulk load funclions. is also equipped with the Verify
lunction. The Verify tunction checks
to
confirm whether
or not the
bulk,dumped data has been transmitled with,
out error, and has been stored successfully.
Actually. the dala that
is
bulk-dumped from the
GP,'
6
is
transmitted back
to
the originating GP·16
in
a manner
Similar to a bulk load. Then,
Ihe newly received data
is
compared with the data existing internally in the originat,
109
GP-16 to check for any discrepancies. The result of
Ihe check appears on the display
of
the originator.
To Next Page
Loading...
Need help?
General
