Rosemount Oxymitter 5000 - Appendix A Safety Data

214 pages

Save Page as PDF

To Next Page

To Previous Page

Instruction Manual

IM-106-350C, Rev 2.2

July 2008

Hazardous Area Oxymitter 5000

http://www.raihome.com

Appendix A Safety Data

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .page A-2

Safety Data Sheet for Ceramic Fiber Products . . . . . . . . . . . . .page A-24

Main Page

Table of Contents7
Essential Instructions11
Preface12
Definitions12
Symbols12
Oxymitter 5000 with Fieldbus Communications13
Component Checklist15
System Overview15
- Scope15
- Foundation Fieldbus Technology17
- System Description17
- System Configuration18
- System Features19
- Handling the Oxymitter21
- System Considerations21
IMPS 4000 (Optional)25
SPS 4001B (Optional)25
- Mounting25
- Operation25
Probe Options25
- Diffusion Elements25
- Abrasive Shield Assembly26
Specifications28
Mechanical Installation34
- Selecting Location34
- Probe Installation34
- IM-106-350C, Rev34
- Remote Electronics Installation42
Electrical Installation with Integral Electronics42
- Connect Line Voltage43
Electrical Installation with Remote Electronics45
- Connect Line Voltage46
- Calibration Handshake Logic I/O46
- Install Interconnecting Cable48
Pneumatic Installation49
- Calibration Gas50
IMPS 4000 Connections50
SPS 4001B Connections50
Verify Installation51
- Mechanical Installation51
- Terminal Block Wiring51
- Hazardous Area Oxymitter 5000 Configuration52
Logic I/O52
- Recommended Configuration56
Verify Installation57
- Mechanical Installation57
- Terminal Block Wiring57
- Hazardous Area Oxymitter 5000 Configuration58
Logic I/O60
- Recommended Configuration61
Power up63
Operation64
- Overview64
Power up67
Start up Oxymitter 5000 Calibration69
Navigating the Local Operator Interface69
- Overview69
- Lockout69
LOI Key Designations70
LOI Menu Tree70
Hazardous Area Oxymitter 5000 Setup at the LOI72
LOI Installation75
Oxymitter 5000 Test Points75
Overview77
Fieldbus Terminal Block Connections77
Off-Line and On-Line Operations78
Logic I/Oconfigurations79
Fieldbus Menu Tree80
FOUNDATION Fieldbus O81
Overview83
General85
Alarm Indications85
Alarm Contacts86
Identifying and Correcting Alarm Indications87
Heater Not Open, but Unable to Reach 736° C Setpoint104
Calibration Passes but Still Reads Incorrectly104
Overview107
Calibration with Keypad107
- Automatic Calibration108
- Semi-Automatic Calibration109
- Manual Calibration with Membrane Keypad110
FOUNDATION Fieldbus O112
Calibration with LOI112
Hazardous Area Oxymitter 5000 Repair114
- Removal and Replacement of Probe114
- Replacement of Entire Electronics (with Housing)115
- Electronic Assembly Replacement116
- Terminal Block Replacement116
- Fuse Replacement120
- Entire Probe Replacement (Excluding Electronics)121
- Heater Strut Replacement122
- Cell Replacement124
- Ceramic Diffusion Element Replacement127
- Contact and Thermocouple Assembly Replacement128
Probe Replacement Parts131
Electronics Replacement Parts134
Model 375 Handheld Communicator135
Asset Management Solutions (AMS)136
By-Pass Packages136
IMPS 4000 Intelligent Multiprobe Test Gas Sequencer137
SPS 4001B Single Probe Autocalibration Sequencer138
O 2 Calibration Gas139
Safety Instructions142
Appendix A164
Safety Data Sheet for Ceramic Fiber Products164
Returning Material171
- APPENDIX B Fieldbus Parameters173
- APPENDIX C Direct176
Alarm Detection184
- Modes184
Status Handling185
Advanced Features186
Application Information186
- Channel186
- L_Type186
- Scaling186
Application Examples187
- Temperature Transmitter187
- Pressure Transmitter Used to Measure Level in an Open Tank188
- Differential Pressure Transmitter to Measure Flow190
- Troubleshooting191
Setpoint Selection and Limiting193
- Bkcal_In194
Feedforward Calculation198
Tracking199
Output Selection and Limiting199
Bumpless Transfer and Setpoint Tracking199
PID Equation Structures199
Reverse and Direct Action199
- Cas199
Reset Limiting200
Block Errors200
Modes200
- Alarm Detection201
Status Handling202
Application Information202
- Closed Loop Control202
Application Examples203
- Basic PID Block for Steam Heater Control203
- Feedforward Control204
- Cascade Control with Master and Slave Loops205
- Bkcal_In205
- Cas_In205
- Ff_Val205
- Bkcal_Out205
- Cascade Control with Override206
Troubleshooting208
Hazardous Area Oxymitter210

Rosemount Oxymitter 5000 - Appendix A Safety Data

Table of Contents

Related product manuals