Sanyo PLC-WU3800 User Manual

26
Basic Operation
Remote Control Operation
Using the remote control for some frequently used operations is advisable. Just pressing one of the buttons
enables you to make the desired operation quickly without calling up the On-Screen Menu.
Press the COMPUTER 1/2, HDMI, VIDEO, S-VIDEO and
COMPONENT buttons on the remote control to select the
input source. See pages 28-29, 38-39 for details.
COMPUTER 1/2, HDMI, VIDEO, S-VIDEO and
COMPONENT buttons
Press the FREEZE button on the remote control to freeze
the picture on the screen. To cancel the Freeze function,
press the FREEZE button again or press any other button.
Fig.1 will appear on the Screen menu while the Freeze
function is working.
FREEZE button
Display the input source information: Input, H-sync freq.,
V-sync freq., Screen, Language, Lamp status, Lamp
counter, Power management, Key lock, PIN code lock
and Remote control (p.61).
INFO. button
Press the D.ZOOM +/- buttons on the remote control to
enter to the Digital zoom +/– mode. See page 37 for details.
D.ZOOM +/- buttons
Remote Control
P
Note:
See the next page for the description of other
buttons.
LAMP button
Press the PIP button on the remote control to enter P in P
or P by P.
Mode of Picture in Picture and input source will be displayed
on the main picture and input source will be displayed on the
sub picture for 10 seconds.
See page 52 for details.
PIP button
Press the LAMP button on the remote control to select the
lamp mode for changing the brightness on the screen.
Auto ......... The brightness according to the input signal
(between High and Eco mode).
High ......... Brighter than the Normal mode.
Normal ..... Normal brightness.
Eco .......... Lower brightness reduces the lamp power
consumption and extends the lamp life.
FREEZE
button
D.ZOOM
buttons
LAMP
button
COMPUTER 1/2
buttons
VIDEO
button
INFO.
button
POINT
buttons
S-VIDEO
button
COMPONENT
button
HDMI
button
PIP button
Fig.1

Sanyo PLC-WU3800 Specifications

General

Matrix size	0.59 \
Projection distance	0.99 - 12.1 m
Vertical scan range	50 - 100 Hz
Horizontal scan range	15 - 100 kHz
Projection technology	LCD
Contrast ratio (typical)	500:1
Screen size compatibility	40 - 300 \
Projector native resolution	WXGA (1280x800)
Keystone correction, vertical	±40 °
Audio input	2
Aspect ratio	16:10
Network ready	Yes
Power supply type	AC
Dimensions (WxDxH)	335.7 x 257.5 x 93.6 mm
Connectivity technology	Wired
Focus	Manual
Digital zoom	16 x
Focal length range	19.2 - 30.2 mm
Noise level	35 dB
Noise level (economic mode)	31 dB
Dot clock scanning frequency	140 MHz
Lamp type	NSHA
Lamp power	275 W
Light source type	Lamp
Service life of light source	2500 h
Service life of light source (economic mode)	3000 h
DVI port	No
Composite video in	-
Serial interface type	RS-232
USB 2.0 ports quantity	0
Supported video modes	1080i, 1080p, 720p
Analog signal format system	NTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
Supported graphics resolutions	1024 x 768 (XGA), 1280 x 1024 (SXGA), 1280 x 800 (WXGA), 1400 x 1050 (SXGA+), 1600 x 1200 (UXGA), 1920 x 1200 (WUXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
Product color	White
AC input voltage	100 - 240 V
Power consumption (standby)	0.7 W
Power consumption (typical)	317 W
Power consumption (PowerSave)	280 W
Cables included	VGA

Weight and Dimensions

Depth	257.5 mm
Width	335.7 mm
Height	93.6 mm
Weight	3500 g