Sanyo PLC-WU3800 User Manual

19
The preparation display will disappear
after 30 seconds.
(See page 56 for Lamp control status.)
Turning On the Projector
Connect the projector’s AC power cord into an AC
outlet. The POWER indicator lights red. Open the lens
cap (see pages 9, 64).
Press the ON/STAND-BY button on the top control or
on the remote control. The POWER indicator lights
green and the cooling fans start to operate. The
preparation display appears on the screen and the
count down starts.
2
3
1
4
After the countdown, the input source that was selected
the last time and the lamp control status icon (see page
56) appear on the screen.
Complete peripheral connections (with a computer,
VCR, etc.) before turning on the projector.
Selected Input Source and Lamp Control
P
Note:
The Filter warning and Lamp replacement icons
may appear on the screen depending on the
usage state of the projector.
Basic Operation
16
Lamp control status
P
Note:
• When the Logo select function is set to Off, the logo will
not be shown on the screen (p.48).
• When Countdown off or Off is selected in the Display
function, the countdown will not be shown on the screen
(p.47).
• When the Input Search function is set to On2, the input
signal will be searched automatically (p.46).
• When Off is selected in the Display function, the Video/
PC selection window and the input signal guidance
window are not shown on the screen (p.47).
5
If there is no signal input when start on the projector,
or the current signal is missed while operating the
projector, the Video/PC selection window will be
displayed on the screen, please move the pointer to
input source desired by pressing the Point  buttons
and press the SELECT button. And then follow the
input signal guidance window to correct the signal and
connection.
If the projector is locked with a PIN code, PIN code input
dialog box will appear. Enter the PIN code as instructed
on the next page.
Video selection
Guidance for Video Input
PC selection
Guidance for PC Input
No signal
Current Input setting : Video
Is signal processed correctly?
Is cable connected properly?
VIDEO
S-VIDEO
No signal
Current Input setting : COMPUTER1 RGB
Is signal processed correctly?
Is cable connected properly?
Video

Sanyo PLC-WU3800 Specifications

General

Matrix size	0.59 \
Projection distance	0.99 - 12.1 m
Vertical scan range	50 - 100 Hz
Horizontal scan range	15 - 100 kHz
Projection technology	LCD
Contrast ratio (typical)	500:1
Screen size compatibility	40 - 300 \
Projector native resolution	WXGA (1280x800)
Keystone correction, vertical	±40 °
Audio input	2
Aspect ratio	16:10
Network ready	Yes
Power supply type	AC
Dimensions (WxDxH)	335.7 x 257.5 x 93.6 mm
Connectivity technology	Wired
Focus	Manual
Digital zoom	16 x
Focal length range	19.2 - 30.2 mm
Noise level	35 dB
Noise level (economic mode)	31 dB
Dot clock scanning frequency	140 MHz
Lamp type	NSHA
Lamp power	275 W
Light source type	Lamp
Service life of light source	2500 h
Service life of light source (economic mode)	3000 h
DVI port	No
Composite video in	-
Serial interface type	RS-232
USB 2.0 ports quantity	0
Supported video modes	1080i, 1080p, 720p
Analog signal format system	NTSC, NTSC 4.43, PAL, PAL M, PAL N, SECAM
Supported graphics resolutions	1024 x 768 (XGA), 1280 x 1024 (SXGA), 1280 x 800 (WXGA), 1400 x 1050 (SXGA+), 1600 x 1200 (UXGA), 1920 x 1200 (WUXGA), 640 x 480 (VGA), 800 x 600 (SVGA)
Product color	White
AC input voltage	100 - 240 V
Power consumption (standby)	0.7 W
Power consumption (typical)	317 W
Power consumption (PowerSave)	280 W
Cables included	VGA

Weight and Dimensions

Depth	257.5 mm
Width	335.7 mm
Height	93.6 mm
Weight	3500 g