SATO HT200e - Page 100

SECTION 5 ： PRESET, TABLE DATA
Page 5-8 SATO HT200e
MASTER LABEL PRINTING FOR PRESET DATA
[RCL]
[
→ ]
[
→ ]
[
→ ]
[
→ ]
[
→ ]
[ENTR]
[ENTR]
ＦＯＲＭＡＴ Ｎｏ
1［
・ ・］
ＨＴ２００ｅ
［ＰＲＥＳＥＴ］
2
Ｐ Ｒ Ｉ Ｎ Ｔ ＳＴＲ ＭＯＤＩＦＹ
ＤＥＬ ＤＵＭＰ ＭＡＳＴＥＲ
［ＰＲＥＳＥＴ］
3 ＰＲＩＮＴ
Ｓ Ｔ Ｒ ＭＯＤＩＦＹ
ＤＥＬ ＤＵＭＰ ＭＡＳＴＥＲ
［ＰＲＥＳＥＴ］
4 ＰＲＩＮＴ ＳＴＲ
Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
ＤＥＬ ＤＵＭＰ ＭＡＳＴＥＲ
［ＰＲＥＳＥＴ］
5 ＰＲＩＮＴ ＳＴＲ ＭＯＤＩＦＹ
Ｄ Ｅ Ｌ ＤＵＭＰ ＭＡＳＴＥＲ
［ＰＲＥＳＥＴ］
6 ＰＲＩＮＴ ＳＴＲ ＭＯＤＩＦＹ
ＤＥＬ
Ｄ Ｕ Ｍ Ｐ ＭＡＳＴＥＲ
［ＰＲＥＳＥＴ］
7 ＰＲＩＮＴ ＳＴＲ ＭＯＤＩＦＹ
ＤＥＬ ＤＵＭＰ
Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
ＰＲＥＳＥＴ ＮＯ ． ＩＮＰＵＴ
8
・ ・・・―・・・・ ＭＡＳＴＥＲ
ＰＲＩＮＴＩＮＧ
9
The screen for the selection of preset printing will
be displayed: Press [
→ ], so that it goes to the
screen for the process No. 3.
Press [RCL], so that it goes from the modes of the
print to the preset.
The screen for the selection of preset storing will
be displayed: Press [
→ ], so that it goes to the
screen for the process No. 4.
The screen for the selection of preset modification
will be displayed: Press [
→ ], so that it goes to the
screen for the process No. 5.
The screen for the selection of preset dump will be
displayed: Press [
→ ], so that it goes to the screen
for the process No. 7.
The screen for the selection of preset deletion will
be displayed: Press [
→ ], so that it goes to the
screen for the process No. 6.
The screen for the selection of preset master will
be displayed: Press [ENTR], so that it goes to the
entry of preset number.
The preset No. that is required to print master label
can be entered: Press [ENTR], so that it prints
master label for the preset specified.
Note that if [ENTR] is pressed without entering a
preset No., the preset data registered will be
printed from the beginning.
While master label is being printed, the screen of
the process No. 9 remains displayed. When print is
complete, it returns to the process No. 8.