SECTION 2: INSTALLATION AND SETUP
SATO HT200e Page 2-21
PROCESS ON THE SCREEN FOR DATA MAINTENANCE MODE
1. Copy for print parameter (From a card to a printer, or opposite direction)
2. Transfer for print parameter (From a card to a printer, or opposite direction)
3. Transfer for preset data (From a card to a printer, or opposite direction)
4. Transfer for font (From a card to a printer, or opposite direction)
5. Transfer for table data (From a card to a printer, or opposite direction)
6. Setting for currency mark
7. Card clear
8. Code setting for EAN country
6 + Power “ON”
[
←
][
→
]
[
←
][
→
]
[
←
][
→
]
[
←
][
→
]
[
←
][
→
]
[
←
][
→
]
[
←
][
→
]
ＰＡＲＡＭＥＴＥＲ ＣＯＰＹ
1
ＰＲＩＮＴＥＲ ←→ ＣＡＲＤ
ＤＡＴＡ ＳＴＯＲＥ／ＲＣＡＬ
Ｌ
2
ＰＲＩＮＴＥＲ ←→ ＨＯＳＴ
ＰＲＥＳＥＴ ＳＴＲ／ＲＣＡＬ
Ｌ
3
ＰＲＩＮＴＥＲ ←→ ＨＯＳＴ
ＦＯＮＴ ＳＴＯＲＥ／ＲＣＡＬＬ
4
ＰＲＩＮＴＥＲ ←→ ＨＯＳＴ
ＴＡＢＬＥ ＳＴＲ／ＲＣＡＬＬ
5
ＰＲＩＮＴＥＲ ←→ ＨＯＳＴ
ＣＵＲＲＥＮＣＹ ＳＥＬＥＣＴ
6
ＣＡＲＤ ＣＬＥＡＲ
7
ＥＡＮ ＣＯＵＮＴＲＹ ＣＯＤＥ
8
５ ０
Press [ENTR], so that it goes to the screen for the
copy of print parameter. Use [
→
] to move to the
process No. 2.
Press [ENTR], so that it goes to the screen for the
transfer of print parameter.
Press [
←
] to go to the process No. 1.
Press [
→
] to go to the process No. 3.
Press [ENTR], so that it goes to the screen for the
transfer of preset data.
Press [
←
] to go to the process No. 2.
Press [ENTR], so that it goes to the screen for the
transfer of table data.
Press [
←
]to go to the process No. 4.
Press [ENTR], so that it goes to the screen for the
font transfer.
Press [
←
] to go to the process No. 3.
Press [
→
] to go to the process No. 5.
Press [ENTR], so that it goes to the screen for the
selection of currency mark.
Press[
←
] to go to the process No. 5.
Press [ENTR], so that it goes to the screen for the
code setting of EAN country. Select value from 00
99. Note that default value id 50.
Press [
←
]to go to the process No. 7.
Press [ENTR], so that it goes to the screen for the
confirmation of card clear.
Press [
←
] to go to the process No. 6.
To Next Page
Loading...
