Home
SATO
Label Maker
TH2 Series
Page 135 (Appendix)
SATO TH2 Series - Appendix; Optional Cutter Information; Sensor and Option Positions; Printer Operation Mode Selection
160 pages
Manual
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
Section 8: Appendix
TH2 Series Op
erator Manual
Page 8-1
APPENDIX
The following informat
ion is provided:
•
8.1 About Optional Cutter
•
8.2 Positions of sensors and op
tions
•
8.3 Operation M
ode Selection
•
8.4 Base Re
ferenc
e Point
•
8.5 Adjustments
134
136
Table of Contents
Main Page
Default Chapter
6
Table of Contents
6
Introduction
9
Features of the Printer
10
Unpacking
10
Included Accessories
10
Parts Identification
11
Installation
15
Site Location
16
Media Selection
16
Loading Media
17
Loading Roll Media
17
To Route the Label When Using the Dispenser
19
Connections
21
Standard Interface Connection
21
To Activate the Connected Interface
21
Connecting the Power Cable
22
Turning on the Power
23
Turning off the Power
23
Charging the Optional Battery Pack with the Optional Battery Charger
24
Charging the Optional Battery Pack with the Printer
25
Installing and Removing the Optional Battery Pack
25
Connecting Optional Scanner
26
Installing Optional SD Card
26
Operation and Configuration
27
Operator Panel
28
To Navigate and Select Item Within the Menu
31
To Input the Field of the Menu
32
Operating Modes
34
Print Menu
36
To Make Print-Out from a Pre-Defined Format
36
To Make Print-Out from a Pre-Loaded Table
38
To Set the Printer to On-Line Mode
39
Main Menu
40
Settings Menu
40
Application Menu
41
To Edit the Pre-Loaded Format
42
To Edit the FIELD Menu
44
When Text Is Selected in the FIELDTYPE Menu
46
When Barcode Is Selected in the FIELDTYPE Menu
48
When Line Is Selected in the FIELDTYPE Menu
51
When Box Is Selected in the FIELDTYPE Menu
52
When Image Is Selected in the FIELDTYPE Menu
53
When Textbox Is Selected in the FIELDTYPE Menu
55
About SOURCETYPE Menu Selection
57
To Edit the Pre-Loaded Table
62
To Edit the F1 Menu
64
To Set the PRINT Menu Appearance
65
Printer Setup Menu
66
When Profile Is Selected in the SETUP Menu
66
When Media Is Selected in the SETUP Menu
69
When Print Ctrl Is Selected in the SETUP Menu
73
When System Is Selected in the SETUP Menu
80
When Regional Is Selected in the SETUP Menu
85
When Network Is Selected in the SETUP Menu (LAN)
88
When Network Is Selected in the SETUP Menu (Wireless LAN)
89
Setting of Wireless LAN Infrastructure Mode
91
Setting of Wireless LAN Ad Hoc Mode
94
Advanced Setup Menu
96
F1 Shortcuts Menu
100
Cleaning and Maintenance
103
Cleaning the Print Head and Platen Roller
104
How to Clean the Printer (Cleaning Kit)
104
How to Clean the Printer (Cleaning Sheet)
105
Easy Replacement of Parts
106
Releasing and Replacing the Print Head
106
Releasing/ Replacing the Platen Roller
107
Adjusting Print Quality
107
Troubleshooting
109
Error Signal Troubleshooting
110
General Description of an Error Message
110
Error Message
110
Troubleshooting Table
113
Interface Troubleshooting
115
Test Print Troubleshooting
116
Hex Dump
116
Test Label Printing
116
Basic Specifications
117
Printer Basic Specifications
117
Optional Accessories Specifications
122
Interface Specifications
125
Interface Types
125
Universal Serial Bus (USB) Interface
126
Basic Specifications of USB Interface
126
Pin Assignments
126
Local Area Network (LAN) Ethernet and Wireless LAN
127
Basic Specifications of LAN
127
Basic Specifications of Wireless LAN
128
Software Specifications
129
TCP/IP Specifications
129
Setting/Displayed Items
130
Wireless LAN Setting
130
Appendix
135
About Optional Cutter
136
To Route the Media When the Cutter Is Installed
136
Cut Position Adjustment
136
Cutter Replacement
137
Positions of Sensors and Options
137
Operation Mode Selection
138
Continuous Mode
138
Tear off Mode
139
Dispensing Mode
140
Cutter Mode
142
Linerless Cutter Mode
144
Journal Mode
145
Tear off Journal Mode
146
Cutter Journal Mode
147
Linerless Cutter Journal Mode
149
Base Reference Point
150
Start of Print Positions
150
Stop Positions
150
Adjustments
151
I-Mark (Pitch Offset (I)) and Gap Sensor (Pitch Offset (G))
151
Dispensing Adjustment (Disp Adj.)
151
Cutter Adjustment (Cutter Adj.)
151
Position Adjustment (Pos Adjust)
151
Pitch Adjustment (Pitch)
151
Offset Adjustment (Offset)
151
License Agreements
153
Sato Group of Companies
159
Related product manuals
SATO TH2
19 pages
SATO TH208
32 pages
SATO S84
298 pages
SATO RFID
26 pages
SATO CG408
102 pages
SATO s84ex
380 pages
SATO s86ex
380 pages
SATO PB2-180
2 pages
SATO CL4NX UHF
2 pages
SATO CL4NX RIDF
10 pages
SATO PB1 Series
2 pages
SATO KENDO 22.6
2 pages
To Next Page
