To Next PageTo Next PageWhat to do if my Selve commeo WS Receiver motor doesn't function and the transmission control light flashes?
If the motor isn't working and the transmission control light flashes, it could be that the receiver/motor is out of radio range. Try reducing the distance. Alternatively, the transmitter might not be programmed into the receiver/motor. In that case, you should program the transmitter.
Why does my Selve commeo WS Receiver awning not extend when the sun is shining?
If your awning doesn't extend when it's sunny, the sun threshold value might be set too high. Try lowering it. Also, check if the system is set to manual mode; if so, set the sliding switch MAN/AUTO to AUTO. The sensor could be positioned in the shade, so try changing its position. Finally, the system may be in wind alarm, so wait until the wind abates.
What to do if Selve Receiver awning remains extended even if there is no sunshine?
If your awning stays extended without sunshine, the sun threshold value might be set too low. Increase the sun threshold value to resolve this.
Why does my Selve commeo WS Receiver awning not retract at heavy winds?
If the awning does not retract during heavy winds, it could be because the sensor is positioned in the lee. Try changing the sensor's position. It's also possible that the wind value is set too high, so have the wind threshold value reset by a specialist.
Why does my Selve Receiver awning retract if there is a slight breeze?
If your awning retracts with only a slight breeze, the wind threshold value is likely set too low. Have the wind threshold value reset by a specialist.
General| Operating voltage | 230 V AC |
|---|---|
| Radio frequency | 868.3 MHz |
| Modulation | FSK |
| Sensitivity | -105 dBm |
| Supply Voltage | 230 V AC |
| Operating Temperature | -20°C to +60°C |
| Type | Receiver |
Specifies the intended and permitted use of the commeo Sensor WS/WSRF.
Illustrates the front and rear views of the commeo Sensor WS/WSRF, identifying its parts.
Lists the components included in the product packaging and required tools for installation.
Guides on choosing an optimal placement for the sensor to ensure proper function and range.
Details the preparation and methods for physically mounting the commeo Sensor WS/WSRF.
Provides step-by-step instructions for connecting the sensor to the mains voltage (230V).
Explains how to pair the hand-held transmitter with the motor or receiver for control.
Details the process of saving the sensor's configuration into the receiver using the transmitter.
Describes how to remove a previously saved sensor from the receiver's memory.
Outlines the default configurable parameter values for the commeo Sensor WS/WSRF.
Explains the purpose and function of programmed delay times for automatic switching.
Guides on adjusting the sun and wind threshold values using a hand-held transmitter.
Illustrates the operation of commeo Multi Send and commeo Send WS 10 hand-held transmitters.
Describes different receiver profiles and their compatibility with sensor functions.
Details the security function of wind automatic and its operation to protect sun protection systems.
Step-by-step guide for setting the wind threshold using the commeo Multi Send transmitter.
Step-by-step guide for setting the wind threshold using the commeo Send WS 10 transmitter.
Explains how LED lights on the transmitter indicate set wind speed thresholds.
Describes how the sun automatic function operates based on light intensity and settings.
Explains the measured light values (Sunny/Cloudy) and delays for sun automatic operation.
Step-by-step guide for setting sun thresholds using the commeo Multi Send transmitter.
Step-by-step guide for setting sun thresholds using the commeo Send WS 10 transmitter.
Explains twilight and darkness settings for awnings and Venetian blinds.
Describes how manual commands affect the automatic sun operation.
Details the operation of the rain sensor and its retraction function for sun protection.
Explains the frost protection function to prevent damage during freezing temperatures.
Describes how to activate and deactivate the test mode to shorten delay times.
Provides guidance on how to properly dispose of the commeo Sensor WS/WSRF as electronic waste.
Lists the technical specifications of the commeo Sensor WS/WSRF, including voltage, dimensions, and frequency.
States the device's conformity with relevant EU directives.
Lists common issues with their causes and solutions for the commeo Sensor WS/WSRF.
Provides contact information for support and instructions on downloading manuals.
