MillipaK PUMP Controller Manual Page 39 07/11/05
CREE P
RA MP
EX T RA
X2
X3
X4
X5
BAT T
MO T OR ( V)
M OT OR (A )
T EM P
T EST
Un used
Ram p s
P ower
St eer
Addit ion al
P erso n alit ies
Syst em
Set up
Fault Lo g
Un used
Syst em
Volt ages
Mo t or
Volt ages
Mo t or
Curre nt s
Heat sink
T em p erat ure
T est Me nu
T OP
Navigation
T he o pera to r m ov es t h ro ugh t h e Calibrat or M ap by pr essin g t he SELE CT k ey . T he solid lin e sh ows t h e pa th t he
th ro ugh t h e m en u st ruct ure when t he SEL ECT k ey is p ressed.
In Serv ice M ode ( no P assword en t ered) o nly t h e it em s sh own wit h a t h ick so lid bor der a re display ed. W hen t he
nex t it em is hidden (E n gin eerin g o r A ll adjust access o nly), t h e calibra to r m ov es on t h e n ext disp lay able it em .
It em s wh ich are n ot co nfigured will a lso be h idde n, ie t he by pass it em s will n o t be disp laye d if t h e byp ass
con t ac to r is n ot co n figured.
In E ngineering M o de ( P asswor d en t er ed) t h e it em s sh own wit h a so lid border are disp lay ed. W hen t he n ex t it em
is hidden (A ll adjust access o nly), th e calibrat or mo ve s o n t h e n ex t disp lay able it em . It em s which a re n o t
con figured will also be h idden .
In All Adjust M ode (P assword en t ered) all t he it ems (so lid an d dash ed bo rders) ar e disp layed.
Direction
By default , th e Calibrat o r m ov es fro m left t o r igh t t h rough t he m en u st ruct ure. I f t h e o p erat or p resse s an d ho lds
th e '+' and '-' k eys for m o re t han 3 seco n ds t he n avigat io n direc tio n ch an ges and t he Calibrat or will m o ve fr om
righ t t o left t hr ough t h e m en u st ruct ure. T he direct io n can be rest o red by h oldin g th e '+' an d '-' k ey s fo r 3 sec on ds
again.
T he dir ect ion is indicat ed by t h e L ED o n t h e Bar Graph . If t he LE D is lit st e adily, t h e direct io n is fro m left t o
righ t , else if t h e L ED is flash ing t h e direct io n is f rom righ t t o left .
Information Items
T he T est m enu o n ly sho ws in fo rm at ion it em s t hat can no t be m o dified. T he o pe rat o r can m o ve up
and do wn t h e m enu usin g t h e '+' an d '-' k ey s. As bef ore, it em s wit h a dash ed bo rder are on ly disp lay ed in All
Adjust M o de. If t h e Op er at o r presses t he SELE CT k ey t he Calibrat or mo v es t o t he n ex t m enu.
Item Identification
T he o pera to r can iden t ify t h e curren t it em by h oldin g down t h e '+' an d '-' ke ys. Fo r ex am ple, h o ldin g down t h e
'+' an d '-' key s o n t he H igh V Cut o ut p erso na lit y will disp lay 1 1.0 9 (M enu 1 1 (I.M A X is m en u 0 ), It em 9 ). T he
op erat o r will use t h e U ser Man ual t o ident if y t h e p erso nalit y fr om t he I D.
Calibrat o r
Refer en ce
SP EE D 1
SPE ED 2
SPE ED 3
SPE ED 4
SPE ED 5
SPE ED 6
SPE ED 7
SPE ED 8
De scr ip tio n
Lift
Speed 1
Lift
Speed 2
Lift
Speed 3
Creep
Speed
T OP
xx x
Service Lev el A cc ess
xx x
En gin eer in g L ev el A ccess
xx x
All Adjust Lev el Access
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
1 2 3 ( 16 ) 4 (1 7) 5 (1 8 ) 6
7 8 9
Speed 1 Co m p 1
Speed 3 Co m p 3
P S Spe ed P S Delay P S Co m p
Creep Sp ee d
Lif t Ram p U p
Cap . Volt age
Battery Voltage
Motor Voltage
Motor Current
T em perat ure
Ac c 1 Dem an d
Acc 1 Volt age
10 1 1
Nacco Calibrator Map for MillipaK Series Pump - 9/11/2001
12
Syst em Stat us
S/W Version
Digital 6 Sw itc hDigital 5 Sw itc hDigital 4 Switc hD igital 3 SwitchD igita l 2 SwitchDigita l 1 Switch
Ser No . D ate Ser No . ID1 Ser No . ID2
Acc 2 D em an d
Acc 2 Volt age
13 14
Digit al I/O Syst em Vo lt ageAn alo gue
Inputs
Accel 1 Z ero V Accel 1 Full V
Spe ed 2 Co m p 2 Accel 2 Zer o V Ac ce l 2 Full V
Spe ed 4 Co mp 4
Spe ed 5 Add / P ri 5
Spe ed 6 Add / P ri 6
Spe ed 7 Add / P ri 7
P S Ra mp Up
Lo w V Cut o utLo w V Star tCurren t L im it
Lift
Speed 4
Lift
Speed 5
Lift
Speed 6
Lift
Speed 7
Ram p Do wn
Seat Delay
Seat Cut s L ift
S/W Sub-Rev
1 5
P ers
Checksum
Syst em Sta te
Ch op Select
To Next Page
Loading...
Need help?
General
