Need help?Do you have a question about the Siemens 1FP1/3 and is the answer not in the manual?
Explains the system of warning notices and their meanings.
Defines who is considered qualified personnel for operating the product.
Notes on the correct usage and application of Innomotics products.
Lists registered and used trademarks.
States the disclaimer regarding the content of the publication.
Introduces the SIMOTICS family of electric motors.
Explains the content and purpose of the manual.
Provides guidance on avoiding hazards and ensuring safe operation.
Details how to access service and support resources.
Provides crucial information about the product's intended use and directives.
Provides overarching safety guidelines, including qualified personnel and 5 safety rules.
Details risks from rotating parts, hot surfaces, chemicals, noise, and electromagnetic fields.
Provides precautions for handling ESD sensitive devices.
Notes on interference immunity, voltages, and special designs.
Defines the intended use and application areas for the motors.
Explains the information found on the motor's rating plate.
Provides guidelines and standards for installing the machine.
Details the types of bearings used and their service life.
Describes the machine's protection type and installation environment.
Lists limit values for humidity, temperature, and altitude.
Details optional integrated and mounted accessories like sensors and brakes.
Highlights safety aspects during plant configuration.
Details safety instructions and procedures for transporting and storing the machine.
Explains the purpose and use of the rotor shipping brace.
Provides crucial information on maintaining adequate cooling.
Warns about dangers of resonance at critical speed ranges.
Covers essential aspects of operating the machine with a converter.
Outlines critical safety instructions for machine installation.
Lists requirements to be met before starting installation work.
General instructions for installing the machine.
Key considerations for aligning and fixing the machine.
General steps for installing the machine.
Instructions for mounting drive output elements and feather key types.
Critical safety instructions before performing electrical connections.
Provides general guidance for connecting the machine.
Information related to the terminal box.
Specifies minimum air clearances between non-insulated parts.
Details requirements for connecting the grounding conductor.
Covers connections for sensors and anti-condensation heating.
Provides information on conductor connections based on terminal size.
Guidance on connecting machines to converters.
Lists final checks to perform before closing the terminal box.
Outlines essential checks and measures before commissioning.
Instructions and measures for switching on the machine.
Details the procedure for conducting a test run.
General safety instructions for operating the machine.
Identifies abnormal conditions indicating incorrect functioning.
Procedures for switching on the machine.
General measures required during stoppages under normal conditions.
Introduces the section on troubleshooting faults.
Lists common electrical faults and their remedial measures.
Lists common mechanical faults and their remedial measures.
Identifies causes and remedies for rolling bearing faults.
Lists causes and remedies for faults in the external fan.
General guidance on maintenance, inspections, and overhauls.
Comprehensive guide to inspection and maintenance procedures.
Checks to perform after installation or repair.
Guidance for general inspections at intervals.
How to assess rolling bearings, advising to contact Service Center.
General maintenance intervals and factors to consider.
Instructions for re-greasing rolling bearings.
General instructions for corrective maintenance.
Details on sealing bearings and installing them.
Information on shaft sealing, dimensions, and alignment.
Information related to the fan component.
Information on optional add-on units.
Instructions on how to order spare and repair parts.
How to find spare parts online using "Spares on Web".
Guidance on ordering and replacing rolling bearings.
Classification of parts into spare, repair, standardized, and other parts.
Lists common machine parts with their part numbers.
Information on purchasing standardized parts.
Introduces exploded drawings for spare parts identification.
Introduces environmental goals and disposal recommendations.
Steps for preparing the machine for disassembly by qualified personnel.
General procedures for dismantling the machine.
Guidance on sorting components for recycling.
Information about the Siemens Product Configurator tool.
General information on tightening torques.
Specific tightening torques for screw and bolt connections.
Tightening torques for terminal boards and grounding.
Tightening torques for various components.
Tightening torques for connecting terminals.
Information on accessing quality documents via SIOS.
To Next Page
General