Siemens SINUMERIK 880 GA2

11 Programming of Cycles 01.93
11.7 Data transfer: R parameter into system memory
@40c <Value 1> <Value 2> <Value>
The compensation data can be written via part program with this command. Permissible
data types are 0...8 and 11...13.
<Value 1> Constant with data type
<Value 2> Constant with data number
<Value 3> Value to be written (R parameter/constant)
Example:
@40c K1 K3 R20 The error curve number (data type 1) of the 3rd IKA relation
(interpolatory compensation with absolute values) is
transferred from R20 into the table.
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
Main group 4/subgroup 1: Transfer R parameter into setting data
@410 <Value 1> <Value>
The address of a setting data value is defined in <Value 1>.
Example:
@410 R80 The maximum working area limitation in the 2nd axis is
loaded with the contents of parameter R80.
@411 <Value 1> <Value>
The byte address of a setting data bit is defined in <Value 1>.
Address area: 5000 to 9999.
@412 <Value 1> <Value 2> <Value>
The byte address of a setting data bit is defined in <Value 1>.
Address area: 5000 to 9999.
The bit address (0 to 7) is given in <Value 2>.
@413 <Value 1> <Value 2 > <Value>
The address of a cycle setting data is defined in <Value 2>.
Where:
<Value 1> Channel no.; when simulating a program, only a cycle machine data from
the channel in which the program is running (no. 0) can be described.
<Value 2> Word address
@414 <Value 1> <Value 2 > <Value>
The byte address of a cycle setting data is defined in <Value 2>.
Where:
<Value 1> Channel no.; when simulating a program, only a cycle machine data from
the channel in which the program is running (no. 0) can be described.
<Value 2> Byte address
@415 <Value 1> <Value 2 > <Value 3> <Value>
The byte address of a cycle setting data bit is defined in <Value 3>.
Where:
<Value 1> Channel no.; when simulating a program, only a cycle machine data from
the channel in which the program is running (no. 0) can be described.
<Value 2> Byte address
<Value 3> Bit address
11–28
© Siemens AG 1991 All Rights Reserved 6ZB5 410-0HD02
SINUMERIK 880, (PG)