What to do if Siemens Measuring Instruments show '24V supply too high'?
If your Siemens Measuring Instruments display '24V supply too high', it's because the battery voltage is too high. To solve this, check the mains voltage. If it's okay, replace K3X...
What does 'Error:Checksum fault in area: ###' mean on Siemens Measuring Instruments and how to resolve it?
If your Siemens Measuring Instruments display 'Error:Checksum fault in area: ###', it indicates a hardware problem. To resolve this, unpower the system and then re-power it. If the message reappears, replace the main board K3X...
What does 'Error:Mod.###,Id.##,Par1.#### Par2.####' mean on Siemens Measuring Instruments and how to resolve it?
If your Siemens Measuring Instruments display 'Error:Mod.###,Id.##,Par1.#### Par2.####', it indicates a software problem. To resolve this, unpower the system and then re-power it. If the message reappears, replace the main board K3X...
What does 'Error:Code execution error, Flag ###' mean on Siemens Measuring Instruments and how to resolve it?
If your Siemens Measuring Instruments display 'Error:Code execution error, Flag ###', it indicates a software problem. To resolve this, unpower the system and then re-power it. If the message reappears, replace the main board K3X...
What does 'read/write ERROR flash?EPROM #' mean on Siemens Measuring Instruments and how to resolve it?
If your Siemens Measuring Instruments display 'read/write ERROR flash?EPROM #', it indicates a read/write problem on the FLASH?EEPROM. Restart the system. If the error is still reported, replace K3X...
What to do if Siemens Measuring Instruments show 'mains POWER OFF'?
If your Siemens Measuring Instruments display 'mains POWER OFF', it means the mains voltage is missing or the fuse ’F9’/’F10’ is blown (10min. delayed). You should check the internal fuses or external mains breakers.
How to fix 'EARTH FAULT to 0V' on Siemens Measuring Instruments?
If you encounter an 'EARTH FAULT to 0V' on your Siemens Measuring Instruments, it indicates that the resistance to earth of potential ‘24V’ is less than 17k ?, and the onboard LED ’LD1’ is lit. To resolve this, remove all pluggable terminals until the fault disappears, then repair the defective wiring.
How to fix 'EARTH FAULT to 24V' on Siemens Measuring Instruments?
If you encounter an 'EARTH FAULT to 24V' on your Siemens Measuring Instruments, it indicates that the resistance to earth of potential ‘24V’ is less than 17k ?, and the onboard LED ’LD1’ is lit. To resolve this, remove all pluggable terminals until the fault disappears, then repair the defective wiring.
What does it mean when Siemens Measuring Instruments display 'battery capacity INSUFFICIENT' and how to fix it?
If your Siemens Measuring Instruments display 'battery capacity INSUFFICIENT', it signifies a negative result from the 'battery load test,' where the voltage doesn't reach 23.5V with a load of 0.7-1A for 10 seconds. To fix this, replace the battery and then reset the system.
What to do if Siemens Measuring Instruments show '24V supply too low'?
If your Siemens Measuring Instruments display '24V supply too low', it's because the battery voltage is too low and the mains are disconnected. To solve this, restore the mains voltage and then reset the system.
General| Measurement Principle | Coriolis |
|---|---|
| Protection Class | IP67 |
| Material | Stainless steel |
| Communication | HART, PROFIBUS PA |
| Outputs | 4-20 mA, pulse/frequency |
| Display | LCD |
| Output Signal | 4-20 mA, pulse/frequency |
| Process Temperature | -50 to +150 °C (-58 to +302 °F) |
Step-by-step guide for system commissioning.
Essential safety guidelines for commissioning personnel.
Guide to configuring settings using the SWE330A PC tool.
Instructions for creating and modifying user-defined text on the panel.
Explains system fault messages and provides troubleshooting steps.
To Next Page
