To Next PageTo Next Page
Need help?Do you have a question about the Socket S700 and is the answer not in the manual?
General| Connectivity | Bluetooth |
|---|---|
| Supported Symbologies | 1D and 2D barcodes |
| Interface | Bluetooth |
| Operating Temperature | 0°C to 50°C |
| Storage Temperature | -20°C to 60°C |
| Humidity | 5% to 95% (non-condensing) |
| Drop Specification | 1.5 meters |
| Power Supply | Rechargeable Lithium-ion battery |
Configures the CHS to revert all settings to factory defaults.
Configures scanner to Basic Mode, discoverable as a keyboard.
Configures scanner to work with an application on iOS.
Configures scanner to Serial Port Profile for Windows/Android.
Configures the scanner to add a carriage return after decoded data.
Configures the scanner to add a tab after decoded data.
Adds carriage return and line feed after decoded data.
Returns only the decoded data, no prefix or suffix.
Configures the scanner to never power off.
Configures scanner to remain on for 8 hours or 4 hours.
Turns the scanner off when not in use.
Enables or disables scanner vibration for successful scans.
Enables or disables scanner beeping for successful scans.
Scan barcodes to enable English, French, German, or Spanish.
Controls iOS onscreen keyboard and beep behavior.
Configures scanner to accept Bluetooth connections in discoverable mode.
Configures scanner to initiate a connection to a device.
Transmits decoded data in packet format.
Transmits decoded data in raw (unpacketed) format.
Configures scanner to automatically reconnect or wait for connection.
Configures double press actions for Ctrl+Z, Ctrl+A, Shift+Tab.
Configures the scanner to never power off.
Configures scanner to remain on for 8 hours.
Enables or disables the transmission of "No Read" messages.
Enables or disables parameter scanning.
Enables or disables parameter pass through for Code-128.
Disables all barcode symbologies.
Sets linear code security levels (1-4).
Enables or disables the UPC-A symbology.
Enables or disables the UPC-E symbology.
Enables or disables the UPC-E1 symbology.
Enables or disables the EAN-8 symbology.
Enables or disables the EAN-13 symbology.
Enables or disables Bookland EAN (ISBN) symbology.
Sets Bookland ISBN format to ISBN-10 or ISBN-13.
Controls how supplementals are decoded (with, ignore, autodiscriminate).
Activates specific supplemental modes like 378/379, 978/979, etc.
Sets UPC/EAN supplemental redundancy level.
Sets UPC/EAN/JAN AIM ID format (Separate, Combined).
Configures transmission of UPC-A check digit.
Configures transmission of UPC-E check digit.
Configures transmission of UPC-E1 check digit.
Configures UPC-A preamble with no preamble, system char, or country code.
Configures UPC-E preamble with no preamble, system char, or country code.
Configures UPC-E1 preamble with no preamble, system char, or country code.
Enables or disables conversion of UPC-E to UPC-A.
Enables or disables conversion of UPC-E1 to UPC-A.
Enables or disables EAN zero extend for EAN-8 to EAN-13.
Enables or disables ISSN EAN symbology.
Enables or disables Code 128 symbology.
Sets discrete lengths or ranges for Code 128.
Enables or disables GS1-128 symbology.
Enables or disables Code 39 symbology.
Enables or disables conversion of Code 39 to Code 32.
Enables or disables Code 32 Prefix.
Sets discrete lengths or ranges for Code 39.
Enables or disables Code 39 Check Digit verification.
Configures transmission of Code 39 Check Digit.
Enables or disables Code 39 Full ASCII mode.
Enables or disables Code 93 symbology.
Sets discrete lengths or ranges for Code 93.
Enables or disables Code 11 symbology.
Sets discrete lengths or ranges for Code 11.
Configures Code 11 Check Digit verification (Disable, One, Two).
Configures transmission of Code 11 Check Digits.
Enables or disables Interleaved 2 of 5 symbology.
Sets discrete lengths or ranges for Interleaved 2 of 5.
Configures 12 of 5 Check Digit verification (Disable, USS, OPCC).
Configures transmission of I 2 of 5 Check Digit.
Enables or disables conversion of I 2 of 5 to EAN-13.
Enables or disables Discrete 2 of 5 symbology.
Sets discrete lengths or ranges for Discrete 2 of 5.
Enables or disables Chinese 2 of 5 symbology.
Enables or disables Matrix 2 of 5 symbology.
Sets discrete lengths or ranges for Matrix 2 of 5.
Enables or disables Matrix 2 of 5 Redundancy.
Configures Matrix 2 of 5 Check Digit verification.
Configures transmission of Matrix 2 of 5 Check Digit.
Configures Inverse 1D for regular, inverse only, or autodetect scanning.
Enables or disables Codabar symbology.
Sets discrete lengths or ranges for Codabar.
Enables or disables CLSI Editing.
Controls NOTIS Editing (keeping or removing abcd).
Enables or disables MSI symbology.
Sets discrete lengths or ranges for MSI.
Configures MSI Check Digit verification (One or Two digits).
Configures transmission of MSI Check Digit.
Configures MSI Check Digit Algorithm (MOD 10 / MOD 11, MOD 10 / MOD 10).
Enables or disables GS1 DataBar Omnidirectional.
Enables or disables GS1 DataBar Limited.
Enables or disables GS1 DataBar Expanded.
Enables or disables conversion of GS1 DataBar to UPC/EAN.
Configures transmission of Symbol, AIM, or None Code ID Characters.
Sets prefix and suffix values for scanning.
Sets data transmission format (e.g., Data As Is).
Configures data transmission with CR/LF, CR, or LF.
Configures data transmission with Suffix 1, Suffix 2, or both.
Configures data transmission with Prefix, Data, and Suffixes.
Configures serial parameters including baud rates 9600 to 115200.
Configures scanner to send raw or packeted decode data.
Sets the time-out for host serial response.
Sets the time-out for host character transmission.
Configures boot up and parameter event reporting.
Enables or disables parameter event reporting.
