Solcon RVS-DN 8 - Control Supply, Control Input and Mains are From the Same Source, Neutral Connected to Terminal 21; Control Supply and Control Input From the Same Source, Neutral not Connected to Terminal 21; Control Supply and Control Input from Separate Sources; Soft Start, Soft Stop and Stop, Control Supply and Control Input from the Same Source

3 • Table of content
__________________________________________________________________________________________
5. Dimensions .............................................................................................................................34
5.1 Standard Models.......................................................................................................................34
5.1.1 Control Module Dimensions ..........................................................................................45
5.2 RVS-DN 1000V and RVS-DN 1200V Models...........................................................................46
5.3 UL/cUL/Marine Models .............................................................................................................47
6. Installation...............................................................................................................................54
6.1 Prior to Installation ....................................................................................................................54
6.2 Mounting ...................................................................................................................................54
6.3 Temperature Range & Heat Dissipation ...................................................................................54
6.3.1 Forced Ventilation .........................................................................................................55
6.3.2 Calculating the Enclosure Size, for Non-Ventilated Metal Enclosure............................55
6.4 Main PCB and Optional PCBs ..................................................................................................55
6.5 Dip Switch Settings on the Main PCB.......................................................................................56
6.5.1 Switch # 1 – Display Modes ..........................................................................................56
6.5.2 Switch # 2 – Tacho Feedback (0-10VDC).....................................................................57
6.5.3 Switch # 3 – Main/D.ADJ.:GENERATOR PARAMETERS............................................57
6.5.4 Switches # 5, 6 – Language Selection ..........................................................................57
6.5.5 Switch # 7 – Expanded Settings ...................................................................................58
6.5.6 Switch # 8 – Software Lock...........................................................................................58
6.6 Internal Fan Control ..................................................................................................................58
6.7 Analog I/O (Option 5) (Terminals T1, T2, Gnd, Out (-), Out (+))..............................................59
6.8 Remote Key-Pad Installation ....................................................................................................60
7. Control Keypad.......................................................................................................................61
7.1 LCD Arrangement.....................................................................................................................61
7.2 Push-Buttons ............................................................................................................................61
7.3 Status LEDs..............................................................................................................................62
7.4 Reviewing and Modifying Parameters ......................................................................................62
7.5 Special Actions Performed in TEST/MAINTENANCE Mode ....................................................62
7.5.1 Run Self Test ................................................................................................................62
7.5.2 View Software Version ..................................................................................................63
7.5.3 Obtain Default Parameters............................................................................................63
7.5.4 Reset Statistical Data....................................................................................................63
7.5.5 Calibrate Voltage and Current (Factory Use Only!) ......................................................64
7.5.6 TEST/MAINTENANCE in RVS-DN 1000V and RVS-DN 1200V...................................64
7.6 Mode Pages..............................................................................................................................65
7.7 Overview of All Mode Pages and Factory Defaults ..................................................................66
7.7.1 Display Mode – Page 0 .................................................................................................68
7.7.2 Main Parameters – Page 1 ...........................................................................................69
7.7.2.1 Overload Calculation..............................................................................................71
7.7.3 Start Parameters – Page 2............................................................................................72
7.7.3.1 Soft Start Parameters.............................................................................................75
7.7.4 Stop Parameters – Page 3............................................................................................77
7.7.4.1 Soft Stop Parameters.............................................................................................78
7.7.5 Dual Adjustment Parameters – Page 4.........................................................................79
7.7.6 Energy Save & Slow Speed Parameters – page 5 .......................................................80
7.7.7 Fault Parameters – Page 6 ...........................................................................................81
7.7.8 I/O Programming Parameters – Page 7........................................................................83
7.7.8.1 Terminal 7 and 8 Programming..............................................................................84
7.7.9 Comm. Parameters – Page 8 – With the Modbus Card................................................85
7.7.10 Comm. Parameters – Page 8 – With the Profibus Card ...............................................85
7.7.11 Statistical Data – page 9 ...............................................................................................86
7.8 Non Adjustable Protection and Fault Reset..............................................................................87
7.8.1 Under/Over Frequency..................................................................................................87
7.8.2 Phase Loss ...................................................................................................................87
7.8.3 Phase Sequence...........................................................................................................87
7.8.4 Wrong Connection ........................................................................................................87
7.8.5 Shorted SCR .................................................................................................................87