SpectraLink 8440 - Page 73

Spectralink 84-Series Series Wireless Telephones Administration Guide
1725-86984-000_P.docx
September 2016 73
Parameter
Permitted Values
Default
np.silent.ringing.toneVolume.usbHeadset
-1000 to 1000
-21
The attribute is set (on adjusting ring volume) when ringing termination is a USB headset and Silent profile is
active. Although the permitted values are -1000 to 1000, the practical limits used by the handset are -50 to 10.
Table 7-8: Meeting Profile Alert Parameters
Parameter
Permitted Values
Default
np.meeting.label
String
Meeting
The name of the profile type.
np.meeting.alert.barcodeBeep.tonePattern
np.meeting.alert.barcodeBeep.vibration
Any tone (see se.pat.misc)
0 or 1
misc2
0
The tone pattern and vibration (1 to enable) for the alert played when a barcode is scanned.
np.meeting.alert.docked.tonePattern
np.meeting.alert.docked.vibration
Any tone (see se.pat.misc)
0 or 1
postiveConfirm
0
The tone pattern and vibration (1 to enable) for the alert played if the handset is docked.
np.meeting.alert.undocked.tonePattern
np.meeting.alert.undocked.vibration
Any tone (see se.pat.misc)
0 or 1
negativeConfirm
0
The tone pattern and vibration (1 to enable) for the alert played if the handset is undocked.
np.meeting.alert.instantMessaging.tonePattern
np.meeting.alert.instantMessaging.vibration
Any tone (see se.pat.misc)
0 or 1
instantMessage
0
The tone pattern and vibration (1 to enable) for the instant message alert.
np.meeting.alert.localHoldNotification.tonePattern
np.meeting.alert.localHoldNotification.vibration
Any tone (see se.pat.misc)
0 or 1
localHoldNotification
0
The tone pattern and vibration (1 to enable) for the local hold notification alert.
np.meeting.alert.lossOfNetwork.tonePattern
np.meeting.alert.lossOfNetwork.vibration
Any tone (see se.pat.misc)
0 or 1
misc1
0
The tone pattern and vibration (1 to enable) for the alert played if the network is lost.
np.meeting.alert.lowBattery.tonePattern
np.meeting.alert.lowBattery.vibration
Any tone (see se.pat.misc)
0 or 1
misc1
0
The tone pattern and vibration (1 to enable) for the alert played if the battery is low.
np.meeting.alert.veryLowBattery.tonePattern
np.meeting.alert.veryLowBattery.vibration
Any tone (see se.pat.misc)
0 or 1
misc1
0
The tone pattern and vibration (1 to enable) for the alert played if the battery is very low.
np.meeting.alert.messageWaiting.tonePattern
np.meeting.alert.messageWaiting.vibration
Any tone (see se.pat.misc)
0 or 1
messageWaiting
0
The tone pattern and vibration (1 to enable) for the alert played if there is a message waiting.
np.meeting.alert.negativeConfirm.tonePattern
np.meeting.alert.negativeConfirm.vibration
Any tone (see se.pat.misc)
0 or 1
negativeConfirm
0
The tone pattern and vibration (1 to enable) for the negative confirmation alert.
np.meeting.alert.positiveConfirm.tonePattern
np.meeting.alert.positiveConfirm.vibration
Any tone (see se.pat.misc)
0 or 1
positiveConfirm
0
The tone pattern and vibration (1 to enable) for the positive confirmation alert.