Technogym Skillmill GO - Adjustments

76 pages

Save Page as PDF

To Next Page

To Previous Page

8. ADJUSTMENTS

No adjustments are required.

Skillmill:

Technical Service Guide - Rev. 2.2

Page 65

e-mail: support@technogym.com

Main Page

Table of Contents5
General Warnings9
Introduction9
Useful Advice10
General Regulations Regarding Service Work10
Personal Protective Equipment10
Technical Specifications11
Mechanical Characteristics12
Overall Dimensions Of The Equipment12
Dimensions And Weight Of Packaging13
Environmental Characteristics14
Conformity With Standards And Directives15
Equipment Coding16
Serial Number Structure17
Position Of Serial Number And Equipment Code18
Wiring Diagrams19
Wiring Diagram, Connect Version19
Wiring Diagram, Console Version20
Wiring Diagram, Go Version20
Cables21
Cu Cables21
Electronic Components25
Voltage Converter (Power Supply)25
Display (Connect Version)25
Display (Console Version)25
Operating Principle25
Low Kit26
Rpm Sensor26
Angle Sensor28
Battery (Console Version)28
Nfc (Connect Version)31
Bluetooth Smart31
Wifi (Connect Version)31
Accessories33
Installation Specifications And Requirements35
Moving and Installing the Equipment35
Lifting And Moving The Equipment36
Troubleshooting & Configuration37
Executable Sw For Diagnostics With Pc37
Structure For Entering Commands38
Reading Firmware Versions38
Cpu) Firmware Version38
Low Kit Braking Table Version39
Better Keypad) Firmware Version39
Firmware Version (Low Kit)39
Wi-Fi) Firmware Version39
Writing The Console Serial Number40
Setting The Facility Url40
Reading and Writing the Serial Numbers and Identification Parameters40
Reading the Console Serial Number40
Viewing The Facility Url41
Writing The Low Kit Serial Number41
Reading The Low Kit Serial Number41
Determining Mac Address42
Wi-Fi And Network Configuration42
Writing The Wep Key Number42
Writing The Access Point Parameter42
Entering a Name for the Network42
Checking Connection Type43
Writing The Console Ip Address43
Writing the GATEWAY Address43
Checking The Ip Address - Default Gateway - Netmask44
Reading The Wi-Fi Power44
Configuring The Realtime Monitor44
Setting Parameters44
Setting The Data Send Period44
Displaying The Monitor Configuration45
Disabling Data Sending45
Enabling Data Sending45
Configuration and Settings for Classes: Skillmill App46
Steps Necessary For Configuring The Skillmill Application47
Display Configuration (Connect Version)48
Troubleshooting50
The Display Does Not Turn On (Connect Version)50
The Display Does Not Turn On (Console Version)51
The Display Only Turns On At A High Speed52
The Effort Level Does Not Change On The Display53
The Effort Level Does Not Change53
The Display Shows An Abnormal Speed (Console Version)53
Login Problems54
Bluetooth Login Problems55
Qr Code Login Problems56
Tgs_Nfc Login Problems57
Brake Table Calibration58
Disassembling The Nfc Board59
Disassembling The Central Handlebar59
Disassembly59
Disassembling The Console59
Necessary Tools59
Disassembling The Side Handlebars60
Disassembling The Post60
Braking System60
Disassembling The Braking System60
Replacing The Brake Cable60
Replacing The Brake Frame60
Replacing The Brake Disc And Pulley61
Replacing The Aluminium Brake Frame61
Replacing The Front Roller62
Replacing The Slats62
Replacing The Platform62
Disassembling The Roller Bearings (Rear Zone)63
Disassembling The Roller Unit63
Disassembling The Roller Unit Bearings63
Disassembling The Angle Sensor63
Adjustments65
Sw Update67
Planned Maintenance69
Tools to be Used71
Revision 1 . 173
Revision 2 . 073
List of Changes for Manual Revision73

Technogym Skillmill GO - Adjustments

Table of Contents

Related product manuals