Tektronix TDS3000B Series - Communication Module Connectors

254 pages

To Next Page

To Previous Page

Getting Started

1-34

TDS3000B Serie s User Manual

Communication Module Connectors

TDS3GV

1. GPIB port. Connect to a controller for remote programmability.

2. RS-232 port. Connec t t o a controller or te rminal for remote

programmability or printing.

3. VGA port. Connect to a VGA monitor to display the

screen image.

Main Page

Table of Contents5
General Safety Summary10
Preface14
Contacting Tektronix14
- Probe Compensation 117
- Signal Path Compensation (SPC) 117
- Functional Check18
- Probe Compensation19
- Adjusting the Oscilloscope Time and Date20
- Signal Path Compensation (SPC)20
Initial Setup17
Product and Feature Description21
- Acquisition Features21
- Signal Processing Features22
- Display Features23
- Measurement Features23
- Trigger Features24
- Convenience Features24
- Optional Features25
Transporting the Oscilloscope26
Operating Positions27
Connecting Power27
- Using Battery Power28
- Operating Safely with Battery Power29
- Installing the Battery30
- Maximizing Operating Time31
- Charging the Battery32
Installing an Application Module33
Installing a Communication Module34
Front-Panel Menus and Controls35
- Using the Menu System35
- Using the Menu Buttons38
- Using the Dedicated Controls40
- Identifying Items in the Display43
- Using Quickmenus45
Front-Panel Connectors47
Rear-Panel Connectors48
Communication Module Connectors50
Taking Simple Measurements54
- Using Autoset54
- Selecting Automatic Measurements55
- Measuring Two Signals56
- Customizing Your Measurements58
Analyzing Signal Detail61
- Looking at a Noisy Signal62
- Separating the Signal from Noise63
- Taking Cursor Measurements64
- Using Delay65
- Measuring Jitter67
Triggering on a Video Signal68
Capturing a Single-Shot Signal72
- Optimizing the Acquisition73
- Using the Horizontal Zoom Function74
Saving Data to the Floppy Disk Drive75
- Saving Screen Images76
- Saving Waveform Data79
Acquisition Controls84
Cursor 384
Cursor98
- YT Cursor Menu98
- XY Cursor Menu103
- Display 3103
Display105
Hard Copy109
Horizontal Controls113
Measure121
Quickmenu129
Save/Recall130
Trigger Controls140
Utility152
Vertical Controls162
E*Scopee Web-Based Remote Control170
Appendix A: Specifications179
Appendix B: Factory Setup193
Appendix C: Accessories197
Appendix D: Probe Basics203
Probe Descriptions203
Probe Compensation204
Tekprobe Interface204
Probe Guard205
Ground Leads205
P3010 High-Frequency Compensation206
P3010 Replaceable Parts and Accessories208
P6139A Replaceable Parts and Accessories210
Using Other Probes212
Supported Active Probes and Adapters213
Unsupported Probes214
Appendix E: Performance Verification215
Performance Verification Procedures215
Appendix F: General Care and Cleaning217
General Care217
Cleaning217
Appendix G: Ethernet Setup219
Your Ethernet Network Information219
Entering the Ethernet Network Settings220
- Networks that Support DHCP and BOOTP220
- Networks that Do Not Support DHCP and BOOTP221
Entering the Network Printer Settings222
Testing Your Ethernet Connection223
- Testing the Oscilloscope Connection223
- Testing Network Printing223
- Testing E*Scope224
Troubleshooting Your Ethernet Connection225
The Instrument Setup Screen226
The Printer Configuration Screen228
The Add Printer Screen229
- Other Network Printer Settings231
- Testing Network Printers231
Ethernet Error Messages232
Ethernet Settings Form233

Tektronix TDS3000B Series - Communication Module Connectors

Table of Contents

Other manuals for Tektronix TDS3000B Series

Related product manuals