Tempest 900 - Page 52

94 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

46

Tempest900 2-Channel Operating Manual

BeltStation Menu

Table of Contents

Table of Contents5
Important Safety Instructions7
A/C Power Warning8
Battery Safety9
Maintenance and Care10
Quick Start Guide11
Theory of Operation13
What's in each Box15
Accessory Items You May Require16
Basestation Overview17
- Volume Control18
- Menu Button18
- Enter Button18
- Front Panel Right19
- Usb Connector20
- In Level Control20
- Out Level Control20
- Beltstation Program Connector21
- Rear Panel Left21
- Ac Power Input Connector21
- DC Power Input Connector21
- Rear Panel Right22
- Aux in Connector22
- Aux out Connector22
- Base Sync in Connector22
- Base Sync out Connector22
- Relay Connector23
- Antenna Connector23
Beltstation Overview24
- Rubberized Access Cover25
- Usb Mini B Connector25
- Beltstation Pairing Connector25
- Belt Clip25
- Battery Compartment25
- Headset Connector26
- Channel Indicator Leds a and B26
Transceiver Controls27
Basestation Setup28
- Power Connections29
- Powering on the Basestation30
- Antenna Location30
- Antenna Configurations31
Remote Transceiver32
Maximizing System Performance and Operational Range33
Configure the Basestation34
- Adjust Sidetone35
- Selecting a Frequency Band35
- Network Number and Lockout Key36
- Set Display Mode to Static or Dynamic38
- Name each Station38
- Basestation Headset Connection and Controls39
- Set the MIC Gain for the Local Headset39
- Front Panel Lock40
- Call Function40
- Gpo Relay Contacts41
- Clear Memory42
- Restore Factory Default42
- Auxiliary Output42
- Reset Memory42
- Beltstation Setup44
- Configure the Beltstation by the Beltstation Menu44
- Configure the Beltstation by the Basestation Interface44
- Steps to Setup the Beltstations45
- Battery Selection and Installation45
- Power Options46
- Adjust Beltstation Slot47
- Pairing with a Basestation47
- Pair Beltstation to Basestation47
- Name Equipment48
- Personal Preferences48
- Set MIC Gain50
- Wireless Iso51
- Wired Intercom Interface to the Basestation53
- Echo Cancellation Menu56
- Test for Echo57
- Manual Null58
- Other Causes of Echo58
- Wire Wiring Schemes59
Modes of Operation60
Split Mode61
Connecting Multiple Basestations62
- Steps to Configure a Multiple Basestation System63
- Audio Connections for Multiple Basestations63
- Master Mode66
- Special Rf Considerations with Multiple Basestations67
- Maximum Number of Collocated Systems68
- Navigate the Beltstation Menu69
- Remove Batteries from Beltstations69
- Install the Rechargeable Battery69
- Charge the Battery69
- Install Aa Alkaline Batteries69
- Navigate the Basestation Menu69
How Do I69
- From the Beltstation70
- Configure Stage Announce and Sa Relay70
- Configure Relays for Individual Beltstations71
- Use the Transceiver71
- Updating Firmware72
Troubleshooting73
- Beltstation will Not Power up75
- Buttons on the Beltstation Do Not Function76
- Tempest Remote Transceiver76
Default Settings77
Tempest Part Numbers78
System Features79
900 Mhz System Specifications80
Basestation Specifications81
Beltstation Specifications82
Remote Transceiver Specifications82
Glossary83
Radio Compliance85
Warranty Information87
Technical Support88
Tempest Block Diagram90
Index92

Other manuals for Tempest 900

Quick Start Guide4 pages