2
© 2008 TOSHIBA TEC CORPORATION All rights reserved e-STUDIO2820C/2830C/3520C/3530C/4520C
SELF-DIAGNOSTIC MODE
2 - 97
Developer material (M) 1204-0 to 8 1205 <Default values of code 1204
(e-STUDIO2820C/2830C/3520C/3530C/
4520C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0/0/0
Sub-code 1: 56,000/56,000/70,000/
70,000/70,000
Sub-code 4: 125,000/125,000/125,000/
125,000/125,000
Developer material (C) 1206-0 to 8 1207 <Default values of code 1206
(e-STUDIO2820C/2830C/3520C/3530C/
4520C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0/0/0
Sub-code 1: 56,000/56,000/70,000/
70,000/70,000
Sub-code 4: 125,000/125,000/125,000/
125,000/125,000
1st transfer roller (K) 1214-0 to 8 1215 <Default values of code 1214
(e-STUDIO2820C/2830C/3520C/3530C/
4520C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0/0/0
Sub-code 1: 500,000/700,000/700,000/
700,000/700,000
Sub-code 4: 1,700,000/1,700,000/
1,700,000/1,700,000/1,700,000
1st transfer roller (Y) 1216-0 to 8 1217 <Default values of code 1216
(e-STUDIO2820C/2830C/3520C/3530C/
4520C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0/0/0
Sub-code 1: 500,000/700,000/700,000/
700,000/700,000
Sub-code 4: 1,700,000/1,700,000/
1,700,000/1,700,000/1,700,000
1st transfer roller (M) 1218-0 to 8 1219 <Default values of code 1218
(e-STUDIO2820C/2830C/3520C/3530C/
4520C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0/0/0
Sub-code 1: 500,000/700,000/700,000/
700,000/700,000
Sub-code 4: 1,700,000/1,700,000/
1,700,000/1,700,000/1,700,000
1st transfer roller (C) 1220-0 to 8 1221 <Default values of code 1220
(e-STUDIO2820C/2830C/3520C/3530C/
4520C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0/0/0
Sub-code 1: 500,000/700,000/700,000/
700,000/700,000
Sub-code 4: 1,700,000/1,700,000/
1,700,000/1,700,000/1,700,000
Transfer belt 1228-0 to 8 1229 <Default values of code 1228
(e-STUDIO2820C/2830C/3520C/3530C/
4520C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0/0/0
Sub-code 1: 500,000/700,000/700,000/
700,000/700,000
Sub-code 4: 1,700,000/1,700,000/
1,700,000/1,700,000/1,700,000
Items
PM management set-
ting <Procedure 4>
*Indicated in 8 digits
Date of previous
replacement
<Procedure 2>
Remarks
To Next Page
Loading...
