e-STUDIO2820C/2830C/3520C/3530C/4520C © 2008 TOSHIBA TEC CORPORATION All rights reserved
SELF-DIAGNOSTIC MODE
2 - 98
Transfer belt cleaning
blade
1232-0 to 8 1233 <Default values of code 1232
(e-STUDIO2820C/2830C/3520C/3530C/
4520C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0/0/0
Sub-code 1: 224,000/224,000/280,000/
280,000/280,000
Sub-code 4: 680,000/680,000/680,000/
680,000/680,000
2nd transfer roller 1240-0 to 8 1241 <Default values of code 1240
(e-STUDIO2820C/2830C/3520C/3530C/
4520C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0/0/0
Sub-code 1: 224,000/224,000/280,000/
280,000/280,000
Sub-code 4: 680,000/680,000/680,000/
680,000/680,000
Pressure roller 1250-0 to 8 1251 <Default values of code 1250
(e-STUDIO2820C/2830C/3520C/3530C/
4520C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0/0/0
Sub-code 1: 112,000/112,000/140,000/
140,000/140,000
Sub-code 4: 340,000/340,000/340,000/
340,000/340,000
Pressure roller separa-
tion finger
1270-0 to 8 1271 <Default values of code 1270
(e-STUDIO2820C/2830C/3520C/3530C/
4520C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0/0/0
Sub-code 1: 112,000/112,000/140,000/
140,000/140,000
Sub-code 4: 340,000/340,000/340,000/
340,000/340,000
Fuser belt 1272-0 to 8 1273 <Default values of code 1272
(e-STUDIO2820C/2830C/3520C/3530C/
4520C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0/0/0
Sub-code 1: 112,000/112,000/140,000/
140,000/140,000
Sub-code 4: 340,000/340,000/340,000/
340,000/340,000
Fuser roller 1274-0 to 8 1275 <Default values of code 1274
(e-STUDIO2820C/2830C/3520C/3530C/
4520C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0/0/0
Sub-code 1: 112,000/112,000/140,000/
140,000/140,000
Sub-code 4: 340,000/340,000/340,000/
340,000/340,000
Fuser belt guide 1276-0 to 8 1277 <Default values of code 1276
(e-STUDIO2820C/2830C/3520C/3530C/
4520C)>
Sub-codes 0, 2, 3, 5, 6, 7, 8: 0/0/0/0/0
Sub-code 1: 112,000/112,000/140,000/
140,000/140,000
Sub-code 4: 340,000/340,000/340,000/
340,000/340,000
Items
PM management set-
ting <Procedure 4>
*Indicated in 8 digits
Date of previous
replacement
<Procedure 2>
Remarks
To Next Page
Loading...
