e-STUDIO2820C/2830C/3520C/3530C/4520C © 2008 TOSHIBA TEC CORPORATION All rights reserved
ERROR CODE AND TROUBLESHOOTING
6 - 10
C5A0 Circuit related service
call
SRAM board not connected (LGC board) P. 6-65
C5A1 SRAM board data abnormality (LGC board) P. 6-65
C900 Connection error between SYS board and LGC
board
P. 6 - 6 5
C940 Engine-CPU abnormality P. 6-65
C962 LGC board ID abnormality P. 6-66
C970 Process related ser-
vice call
High-voltage transformer abnormality: Leakage of
the main charger is detected.
P. 6-102
C9E0 Circuit related service
call
Connection error between SLG board and SYS
board
P. 6 - 6 6
CA00 Image control related
service call
color registration abnormality P. 6-88
CA10 Laser optical unit
related service call
Polygonal motor abnormality: The polygonal motor
is not rotating normally.
P. 6 - 6 8
CA20 H-Sync detection error: H-Sync signal detection PC
board cannot detect laser beams.
P. 6 - 6 9
CB00 Finisher related ser-
vice call
Finisher not connected: Communication error has
occurred between the equipment and finisher. [MJ-
1101]
P. 6 - 7 1
CB01 Finisher communication error: Communication error
has occurred between the equipment and finisher.
[MJ-1101]
P. 6 - 7 1
CB10 Entrance motor abnormality: The entrance motor is
not rotating normally. [MJ-1101]
P. 6 - 7 1
CB11 Buffer tray guide motor abnormality: The buffer tray
guide motor is not rotating or the buffer tray guide is
not moving normally. [MJ-1101]
P. 6 - 7 2
CB12 Buffer roller drive motor abnormality: The buffer
roller drive motor is not rotating or the buffer roller is
not moving normally. [MJ-1101]
P. 6 - 7 2
CB30 Tray 1/Tray 2 shift motor abnormality: Tray 1/Tray 2
shift motor is not rotating or delivery tray is not mov-
ing normally. [MJ-1030]
Movable tray shift motor abnormality: The movable
tray shift motor is not rotating or the movable tray is
not moving normally. [MJ-1101]
P. 6 - 7 2
CB31 Movable tray paper-full detection error: The actua-
tor of the movable tray paper-full detection sensor
does not move smoothly. [MJ-1101]
P. 6 - 7 3
CB40 Rear aligning plate motor abnormality: Rear align-
ing plate motor is not rotating or aligning plate is not
moving normally. [MJ-1030]
Front alignment motor abnormality: The front align-
ment motor is not rotating or the front alignment
plate is not moving normally. [MJ-1101]
P. 6 - 7 3
CB50 Staple motor abnormality: Staple motor is not rotat-
ing or stapler is not moving normally. [MJ-1030]
Staple unit abnormality: Staple unit is not moving
normally. [MJ-1031]
Stapler home position error: The stapler home posi-
tion sensor does not work. [MJ-1101]
P. 6 - 7 4
CB51 Stapler shift home position error: The stapler is not
at the home position. [MJ-1101]
P. 6 - 7 5
CB60 Stapler shift motor abnormality: Stapler shift motor
is not rotating or staple unit is not moving normally.
[MJ-1030/1101]
P. 6 - 7 5
Error code Classification Contents Troubleshooting
To Next Page
Loading...
