Trimble R7 - Trimble R8 GPS Receiver

222 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

SECTION

II

ITRIMBLE R8 GPS RECEIVER

Table of Contents

Trimble® R7/R8 GPS Receiver User Guide1
Introduction13
- Related Information13
- Warnings and Cautions14
- Technical Assistance15
- Your Comments15
Trimble R7 GPS Receiver17
Overview19
- Introduction20
- Features20
- Use and Care21
- COCOM Limits22
Setting up the Receiver23
- Introduction24
- Parts of the Receiver24
- Setup Guidelines30
- Postprocessed Setup32
- PoleMounted Setup34
- Backpack Setup40
- Other System Components42
General Operation49
- Introduction50
- Button Functions50
- LED Behavior51
- Starting and Stopping the Receiver53
- Logging Data54
  - Logging internally54
  - Logging to a Trimble controller55
- Resetting to Defaults55
- Formatting a CompactFlash Card56
- Batteries and Power57
Configuration65
- Introduction66
- Configuring the Receiver in Real Time66
- Configuring the Receiver Using Application Files67
- Application Files67
Transferring Data73
- Introduction74
- Connecting to the Office Computer75
- Transferring Data77
- Transferring Files Directly from a CompactFlash Card78
- Deleting Files in the Receiver80
- Supported File Types80
Software Utilities81
- Introduction82
- GPS Configurator Software82
  - Installing GPS Configurator82
  - Configuring the Trimble R7 receiver83
- WinFlash Software83
Specifications91
- Introduction92
- Physical Specifications92
- Positioning Specifications93
- Technical Specifications94
Default Settings95
- Introduction96
- Default Settings97
- Resetting to Factory Defaults98
- Examples99
Cables and Connectors103
- Introduction104
- Port 1, 2, and 3 Connectors104
- Power/serial data cable106
- Event Marker/1PPS Cable107
- GPS Antennas and Cables109
Event Marker Input and 1PPS Output111
- Introduction112
- Event Marker Input112
  - Enabling and configuring event marker input112
- 1PPS Output114
Trimble R8 GPS Receiver119
Overview121
- Introduction122
- Features122
- Use and Care124
- COCOM Limits124
Setting up the Receiver125
- Introduction126
- Parts of the Receiver126
  - Front panel126
  - Lower housing127
- Setup Guidelines129
- PoleMounted Setup130
- Other System Components131
  - Radios131
  - Cellular modems and external radios133
General Operation135
- Introduction136
- Button Functions137
- LED Behavior137
  - LED flash patterns138
- Starting and Stopping the Receiver138
- Logging Data139
  - Logging internally139
  - Logging to a Trimble controller140
- Resetting to Defaults140
- Batteries and Power141
Configuration145
- Introduction146
- Configuring the Receiver in Real Time146
- Configuring the Receiver Using Application Files147
- Application Files147
Software Utilities151
- Introduction152
- GPS Configurator Software152
  - Installing GPS Configurator152
  - Configuring the Trimble R8 receiver153
- WinFlash Software153
Specifications163
- Introduction164
- Physical Specifications164
- Positioning Specifications165
- Technical Specifications166
Default Settings169
- Introduction170
- Default Settings171
- Resetting to Factory Defaults172
  - Default behavior172
  - Power up settings172
Cables and Connectors173
- Introduction174
- Port 1 and 2 Connectors174
- Power/Serial Data Cables176
Appendixes Trimble R7 / Trimble R8179
NMEA-0183 Output181
- Introduction182
- NMEA-0183 Outputs182
- Common Message Elements184
  - Message values184
- NMEA Messages185
RTCM Output201
- RTCM Output202
- Message Scheduling203
Troubleshooting205
Index211

Related product manuals

Trimble EZ-Guide 500

Trimble EZ-Guide 250