Vishay 7000 - Page 4

Vishay Micro-Measurements System 7000 Programmer’s Reference Manual
Page 4 of 142
6.5.4.14 ConfigureStrainGageChannelBridgeSettings Method ___________________________________________ 81
6.5.4.15 ConfigureHighLevelCardExcitation Method __________________________________________________ 82
6.5.4.16 ConfigureThermocoupleChannel Method ____________________________________________________ 82
6.5.4.17 ConfigureLVDTCardExcitation Method _____________________________________________________ 83
6.5.4.18 ConfigureLVDTChannelInputConnections Method ____________________________________________ 84
6.5.4.19 SetDefaultFilter Method__________________________________________________________________ 84
6.5.4.20 SetFIRFilterCoefficients Method ___________________________________________________________ 85
6.5.4.21 SetDateTimeMethod ____________________________________________________________________ 86
6.5.4.22 ConfigureOnlineDataTransfer Method_______________________________________________________ 86
6.5.4.23 SetScannerNetworkConfiguration Method ___________________________________________________ 87
6.5.4.24 SetBoxID Method ______________________________________________________________________ 88
6.5.5 Data _____________________________________________________________________________89
6.5.5.1 GetStaticADCReading Method _____________________________________________________________ 89
6.5.5.2 GetLastDataFileInformation Method _________________________________________________________ 89
6.5.6 Utilities___________________________________________________________________________91
6.5.6.1 GetControlModuleInformation Method _______________________________________________________ 91
6.5.6.2 GetFreeSpace Method ____________________________________________________________________ 92
6.5.6.3 GetCardStatusMethod ____________________________________________________________________ 92
6.5.6.4 DetectCards Method______________________________________________________________________ 93
6.5.6.5 GetCardInformation Method _______________________________________________________________ 94
6.5.6.6 Flash System LEDs Method________________________________________________________________ 95
6.5.6.7 ResetCard Method _______________________________________________________________________ 95
6.5.6.8 ShuntCalEnable Method __________________________________________________________________ 96
6.5.6.9 RemoteCalEnable Method _________________________________________________________________ 96
6.5.6.10 ClearErrors Method _____________________________________________________________________ 97
6.5.6.11 GetErrorMessage Method ________________________________________________________________ 97
6.5.6.12 RetrieveFile Method_____________________________________________________________________ 98
6.5.6.13 RetrieveLastDataFile Method _____________________________________________________________ 98
6.5.6.14 ListFiles Method _______________________________________________________________________ 99
6.5.6.15 DeleteFile Method ______________________________________________________________________ 99
6.5.6.16 DeleteLastDataFile Method ______________________________________________________________ 100
6.5.6.17 CancelFileTransferMethod_______________________________________________________________ 100
6.6 IVMM7000DATATRANSFERSTATUS INTERFACE DESCRIPTION ___________________________________101
6.6.1 Properties________________________________________________________________________101
6.6.1.1 BytesTransferred Property (Read/Write) _____________________________________________________ 101
6.6.1.2 PercentComplete Property (Read/Write) _____________________________________________________ 101
6.6.1.3 TotalBytes Property (Read/Write) __________________________________________________________ 102
6.6.1.4 ErrorStatus Property (Read/Write)__________________________________________________________ 102
6.6.1.5 TransferComplete Property (Read/Write) ____________________________________________________ 102
7 LOW-LEVEL COMMAND SET ____________________________________________________________103
7.1 CARD AND CHANNEL MASK NOTATION _____________________________________________________103
7.2 COMMAND/QUERY SYNTAX ______________________________________________________________104
7.3 RESPONSE SYNTAX _____________________________________________________________________104
7.3.1 Example Responses ________________________________________________________________105
7.4 COMMAND DESCRIPTIONS _______________________________________________________________106
7.4.1 Action Group _____________________________________________________________________106
7.4.1.1 Start Scanning Command_________________________________________________________________ 106
7.4.1.2 Stop Scanning Command_________________________________________________________________ 106
7.4.1.3 Start Manual Recording Command _________________________________________________________ 106
7.4.1.4 Stop Manual Recording Command _________________________________________________________ 106
7.4.1.5 Arm Command_________________________________________________________________________ 107
7.4.1.6 Disarm Command ______________________________________________________________________ 107
7.4.1.7 Start Online Data Transfer ________________________________________________________________ 107
7.4.1.8 Stop Online Data Transfer ________________________________________________________________ 107
7.4.1.9 Synchronize Networked Scanners __________________________________________________________ 108
7.4.1.10 Start Scanning on Networked Scanners _____________________________________________________ 108
7.4.2 Recording Group __________________________________________________________________109
7.4.2.1 Manual Recording Mode _________________________________________________________________ 109
7.4.2.2 Set Pre-trigger Buffer Size for Manual Recording Command _____________________________________ 109
7.4.2.3 Set Time-Based Recording Mode Command__________________________________________________ 110
7.4.2.4 Set Time-Based Recording Count Command _________________________________________________ 110
7.4.2.5 Set Time-Based Recording Delay Command__________________________________________________ 111
7.4.2.6 Set Time-Based Recording Skip Count Command _____________________________________________ 111