Vishay Micro-Measurements System 7000 Programmer’s Reference Manual
Page 5 of 142
7.4.2.7 Set Time-Based Recording Burst Count Command _____________________________________________ 112
7.4.2.8 Set Time-Based Recording Burst Skip Count Command_________________________________________ 112
7.4.2.9 Set Limits-Based Recording Setting ________________________________________________________ 113
7.4.2.10 Set Limits-Based Recording Mode Command ________________________________________________ 113
7.4.2.11 Set Limits-Based Recording Skip Count Command ___________________________________________ 114
7.4.2.12 Set Limits-Based Recording Burst Count Command___________________________________________ 114
7.4.2.13 Set Limits-Based Recording Burst Skip Count Command_______________________________________ 115
7.4.3 Scan Group ______________________________________________________________________116
7.4.3.1 Set Scan Rate Command _________________________________________________________________ 116
7.4.3.2 Create Scan List Command _______________________________________________________________ 116
7.4.3.3 AutoStop Command_____________________________________________________________________ 117
7.4.3.4 Get Last Data File Info___________________________________________________________________ 117
7.4.3.5 Set Box ID from Scan Header Command ____________________________________________________ 118
7.4.3.6 Set Project Name to Scan Header File Command ______________________________________________ 118
7.4.3.7 Set Scan Session Descriptor to Scan Header File Command ______________________________________ 118
7.4.3.8 Set Scan Session GUID to Scan Header File Command _________________________________________ 119
7.4.3.9 Set Scan Session IP Address to Scan Header File Command _____________________________________ 119
7.4.3.10 Set the Size of the Scan Buffer____________________________________________________________ 119
7.4.4 Limits Group _____________________________________________________________________120
7.4.4.1 Set Limit Type Command ________________________________________________________________ 120
7.4.4.2 Set Number of Limit Event Conditions Command _____________________________________________ 120
7.4.4.3 Set Limit Event Condition Command _______________________________________________________ 121
7.4.4.4 Set Lower Limit Value Command __________________________________________________________ 121
7.4.4.5 Set Upper Limit Value Command __________________________________________________________ 122
7.4.4.6 Set Pre-trigger Buffer Size Command _______________________________________________________ 122
7.4.4.7 Set Post-trigger Buffer Size Command ______________________________________________________ 122
7.4.4.8 Ignore or Accept Sync (Global) Limits ______________________________________________________ 123
7.4.4.9 Set Pre-trigger Buffer Size Command for Sync (Global) Limits ___________________________________ 123
7.4.4.10 Set Post-trigger Buffer Size Command for Sync (Global) Limits _________________________________ 123
7.4.5 Card Group ______________________________________________________________________124
7.4.5.1 Get Card Information Command (AIM/Interface Card)__________________________________________ 124
7.4.5.2 Set Excitation Command _________________________________________________________________ 125
7.4.5.3 Get Free Space Command ________________________________________________________________ 125
7.4.5.4 Card Status____________________________________________________________________________ 126
7.4.5.5 Card Reset ____________________________________________________________________________ 126
7.4.5.6 Excitation Output Enable/Disable __________________________________________________________ 127
7.4.5.7 Aim Temperature Sensor Query____________________________________________________________ 127
7.4.5.8 Set LVDT Excitation Frequency ___________________________________________________________ 127
7.4.6 Channel Group____________________________________________________________________128
7.4.6.1 Asynchronous Read A/D Converter Command ________________________________________________ 128
7.4.6.2 Set Channel Recording Group Command ____________________________________________________ 128
7.4.6.3 Set FIR Filter Command _________________________________________________________________ 128
7.4.6.4 Shunt Calibration Resistor Enable / Disable __________________________________________________ 129
7.4.6.5 Dummy Resistor Selection________________________________________________________________ 129
7.4.6.6 Enable Half-Bridge _____________________________________________________________________ 129
7.4.6.7 Remote Calibration Resistor Enable Disable __________________________________________________ 130
7.4.6.8 Set / Query Thermocouple Type ___________________________________________________________ 130
7.4.6.9 Assign a Limit Event Condition to a Channel(s) _______________________________________________ 131
7.4.6.10 Set Default Filter Command______________________________________________________________ 131
7.4.6.11 Set LVDT Demodulator Source ___________________________________________________________ 132
7.4.7 File Group _______________________________________________________________________133
7.4.7.1 Retrieve File___________________________________________________________________________ 133
7.4.7.2 List Files______________________________________________________________________________ 134
7.4.7.3 Delete File ____________________________________________________________________________ 134
7.4.7.4 Cancel File Transfer _____________________________________________________________________ 135
7.4.7.5 List Files in Control Module ______________________________________________________________ 135
7.4.7.6 Retrieve File from Control Module _________________________________________________________ 135
7.4.7.7 Delete File from Control Module___________________________________________________________ 136
7.4.7.8 Verify the Checksum of a Control Module File ________________________________________________ 136
7.4.8 System Group _____________________________________________________________________137
7.4.8.1 Set Date/Time _________________________________________________________________________ 137
7.4.8.2 Set IP Configuration Information___________________________________________________________ 138
7.4.8.3 Get Free Space Command ________________________________________________________________ 138
7.4.8.4 Configure Online Data ___________________________________________________________________ 139
7.4.8.5 Define Scanner’s Network Configuration ____________________________________________________ 139
To Next Page
Loading...