VTI Instruments EX1000A - Page 126

VTI Instruments Corp.
126 EX10xxA Function Calls
API
Description
vtex10xxA_get_arm_count
Returns the arm count value.
vtex10xxA_get_arm_delay
Returns the arm delay.
vtex10xxA_get_arm_infinite
Returns the enabled status of an infinite arm
count.
vtex10xxA_get_arm_lan_eventID
Returns the event ID of a LAN arm event.
vtex10xxA_get_arm_lan_filter
Returns the filter for the LAN arm event.
vtex10xxA_get_arm_source
Returns the enabled arm source events.
vtex10xxA_get_arm_sourceEx
Returns the arm source events including LAN
events.
vtex10xxA_get_calibration_file
Returns the calibration file data for the specified
buffer.
vtex10xxA_get_calibration_running
Indicates if calibration is currently in progress.
vtex10xxA_get_channel_conversion
Returns the engineering units (EU) conversion of
a specified channel.
vtex10xxA_get_channel_range
Returns the input range of a voltage channel.
vtex10xxA_get_channel_type
Returns whether specified channel is voltage or
thermocouple only channel.
vtex10xxA_get_dio_input
Returns the current input state of the digital I/O
port.
vtex10xxA_get_dio_limit_event
Returns the enabled DIO limit events.
vtex10xxA_get_dio_limit_event_invert
Returns the inverted operation of a DIO channel
linked as a limit event.
vtex10xxA_get_dio_limit_event_latch
Returns the latch operation of a DIO channel
linked as a limit event.
vtex10xxA_get_dio_output
Returns the programmed output state of the digital
I/O port.
vtex10xxA_get_dio_output_enable
Returns the output enable state of the digital I/O
port.
vtex10xxA_get_fifo_config
Returns the data format and overflow behavior of
the FIFO memory.
vtex10xxA_get_fifo_count
Returns the number of data pages (scans) in the
FIFO memory.
vtex10xxA_get_filt_freq
Returns current low-pass filter cutoff frequency of
a specified channel.
vtex10xxA_get_init_cont
Returns the enabled status of init continuous
mode.
vtex10xxA_get_lan_event_domain
Returns the LAN domain for the instrument.
vtex10xxA_get_lan_event_source_state
Returns the current arm and trigger state of the
LAN events.
vtex10xxA_get_lan_eventlog_count
Returns the number of event log entries logged in
the instrument.
vtex10xxA_get_lan_eventlog_enabled
Returns the current status of the event log.
vtex10xxA_get_lan_eventlog_overflowmode
Returns the LAN event log overflow mode.
vtex10xxA_get_limit_set0
Returns the limit set 0 values of a specified
channel.
vtex10xxA_get_limit_set0_manual
Returns the manual entry control of limit set 0
values of a specified channel.
vtex10xxA_get_limit_set1
Returns the limit set 1 values of a specified
channel.
vtex10xxA_get_linear_correction
Returns linear correction of a voltage channel.
vtex10xxA_get_model
Returns the instrument’s model name.
vtex10xxA_get_OTD_enable
Returns a channel’s open transducer detection
status.
vtex10xxA_get_ptp_info
Returns the instrument’s PTP master and
synchronization information.
vtex10xxA_get_scanlist
Returns the current scan list.
vtex10xxA_get_self_test_result
Returns the self test result (Currently supported
only in RX10xx)
vtex10xxA_get_self_test_running
Returns the running status of self test result.
(Currently supported only in RX10xx)
vtex10xxA_get_serialNumber
Returns the serial number of the device.