VTI Instruments EX1000A - Page 127

www.vtiinstruments.com
EX10xxA Function Calls 127
API
Description
vtex10xxA_get_system_time
Returns the instrument’s current time in seconds.
vtex10xxA_get_trig_lan_eventID
Returns the event ID of a LAN trigger event.
vtex10xxA_get_trig_lan_filter
Returns the filter for a LAN trigger event.
vtex10xxA_get_trigger_count
Returns the trigger count value.
vtex10xxA_get_trigger_delay
Returns the trigger delay.
vtex10xxA_get_trigger_infinite
Returns the enabled status of an infinite trigger
count.
vtex10xxA_get_trigger_source
Returns the trigger source excluding LAN events.
vtex10xxA_get_trigger_sourceEx
Returns the trigger source including LAN events.
vtex10xxA_get_trigger_timer
Queries the timer interval for the timer source
event.
vtex10xxA_get_user_cjc_enable
Returns the enabled status of a user-defined CJC
temperature of a specified channel.
vtex10xxA_get_user_cjc_temp
Returns the user-defined CJC temperature of a
specified channel.
vtex10xxA_get_user_conversion
Returns the user-defined conversion polynomials.
vtex10xxA_get_vtb_input
Returns the current input state of the trigger bus.
vtex10xxA_get_vtb_output
Returns the programmed output state of the trigger
bus.
vtex10xxA_get_vtb_output_enable
Returns the output enable state of the trigger bus.
vtex10xxA_get_vtb_wiredor
Returns the Wired-OR state for each LXI Trigger
Bus channel.
vtex10xxA_get_vtb_wiredor_bias
Returns the Wired-OR bias enable state for each
LXI trigger bus channel.
vtex10xxA_init
Opens an instrument programming session.
vtex10xxA_init_imm
Performs a trigger initialize.
vtex10xxA_lock
Attempts to acquire a lock on the instrument.
vtex10xxA_pop_logged_LAN_event
Returns an oldest event log entry in the
instrument.
vtex10xxA_read_fifo
Retrieves acquisition data.
vtex10xxA_read_fifoEx
Retrieves acquisition data with timestamps and
CJC data.
vtex10xxA_reset
Performs an instrument reset.
vtex10xxA_reset_fifo
Clears the FIFO memory.
vtex10xxA_reset_trigger_arm
Performs a reset of the trigger configuration
parameters.
vtex10xxA_revision_query
Returns the release revision of the instrument
driver and embedded firmware.
vtex10xxA_self_cal_clear
Clears the current self cal data.
vtex10xxA_self_cal_clear_stored
Clears self cal data from nonvolatile memory.
vtex10xxA_self_cal_get_status
Returns the completion status of self-calibration.
vtex10xxA_self_cal_init
Performs an instrument self-calibration.
vtex10xxA_self_cal_is_stored
Returns the presence of self cal data in nonvolatile
memory.
vtex10xxA_self_cal_load
Loads nonvolatile self cal data as the current self
cal data.
vtex10xxA_self_cal_store
Stores the current self cal data into nonvolatile
memory.
vtex10xxA_self_test
Performs a self-test in synchronous mode.
(Currently supported only in RX10xx.)
vtex10xxA_self_test_init
Performs a self test operation in asynchronous
mode. (Currently supported only in RX10xx.)
vtex10xxA_set_alarm
Sets the alarm time, period, and count for the LXI
alarm source event.
vtex10xxA_set_alarm_enable
Enables or disables the use of the LXI alarm.
vtex10xxA_set_arm_count
Sets the arm count value.
vtex10xxA_set_arm_delay
Sets the arm delay.
vtex10xxA_set_arm_infinite
Enables or disables the use of an infinite arm
count.
vtex10xxA_set_arm_lan_eventID
Sets the event ID of LAN arm event.