www.vtiinstruments.com
EX10xxA Function Calls 277
#define VTEX10XXA_ERROR_INVALID_TRIG_INF_VALUE
Invalid trigger infinite value.
#define VTEX10XXA_ERROR_INVALID_ARM_INF_VALUE
Invalid arm infinite value.
#define VTEX10XXA_ERROR_INVALID_NUM_SCANS
#define VTEX10XXA_ERROR_READ_FIFO_TIMEOUT
#define VTEX10XXA_ERROR_STRMING_DATA_ENABLED
Streaming data already enabled.
#define VTEX10XXA_ERROR_ENABLING_STRMING_DATA
Enabling streaming data failed.
#define VTEX10XXA_ERROR_STRMING_DATA_NOT_ENABLED
Streaming data not enabled.
#define VTEX10XXA_ERROR_DISABLING_STRMING_DATA
Disabling streaming data failed.
#define VTEX10XXA_ERROR_INSUFFICIENT_FIRMWARE_REV
Insufficient firmware revision.
#define VTEX10XXA_ERROR_VXI_11
#define VTEX10XXA_ERROR_INVALID_FILTER_FREQ
Invalid filter frequency.
#define VTEX10XXA_ERROR_STRMIN_ALREADY_ENABLED
Streaming data already enabled on instrument.
#define VTEX10XXA_ERROR_INVALID_NUM_ENTRIES
Invalid number of entries.
#define VTEX10XXA_ERROR_NEGATIVE_TIME
#define VTEX10XXA_ERROR_DEVICE_LOCKED
#define VTEX10XXA_ERROR_DEVICE_NOT_LOCKED
#define VTEX10XXA_ERROR_CALIBRATION_IN_PROGRESS
#define VTEX10XXA_ERROR_CALIBRATION_MISSING
#define VTEX10XXA_ERROR_TRIGGER_SYSTEM_ERROR
#define VTEX10XXA_ERROR_INSUFFICIENT_UPTIME
Insufficient uptime for requested operation.
#define VTEX10XXA_ERROR_OUT_OF_LINK_IDS
Maximum number of link IDs exceeded.
#define VTEX10XXA_ERROR_INVALID_LINK_ID
#define VTEX10XXA_ERROR_DUPLICATE_SCANLIST_CHNL
Duplicate channel In scanlist.
#define VTEX10XXA_ERROR_SELF_CAL_MISSING
Self-calibration missing.
#define VTEX10XXA_ERROR_UNKNOWN_FIRMWARE_ERROR
#define VTEX10XXA_ERROR_INVALID_DIO_LIMIT
#define VTEX10XXA_BOOLEAN_OUTA_RANGE
Out of range Boolean value.
#define VTEX10XXA_NOT_A_VALID_RSRC
Not a valid resource string.
#define VTEX10XXA_ERROR_ALREADY_LOCKED_U
Instrument already locked by this host.
#define VTEX10XXA_ERROR_ALREADY_LOCKED_NU
Instrument already locked by another host.
#define VTEX10XXA_ERROR_ALREADY_UNLOCKED
Instrument is not locked at this time.
#define VTEX10XXA_ERROR_NONVOL_SELF_CAL_MISSING
Nonvolatile self calibration data missing.
#define VTEX10XXA_ERROR_FIFO_EMPTY
#define VTEX10XXA_ERROR_STRING_TOO_BIG
Input buffer contains too many characters.
#define VTEX10XXA_ERROR_PTP_NOT_RUNNING
Precision time protocol not running. Try
reconfiguring time settings, or a power cycle.
#define VTEX10XXA_ERROR_INVALID_BOOLEAN_VALUE
#define VTEX10XXA_ERROR_WIREDOR_MUST_BE_SET
#define VTEX10XXA_ERROR_INVALID_TIMER_COUNT
#define VTEX10XXA_ERROR_INVALID_TIMER_TIME
#define VTEX10XXA_ERROR_INVALID_LAN_SOURCE
#define VTEX10XXA_ERROR_INVALID_LAN_EVENT_DOMAIN
#define VTEX10XXA_ERROR_INVALID_LAN_EVENT_EVENTID
#define VTEX10XXA_ERROR_INVALID_LAN_EVENT_FILTER
#define VTEX10XXA_ERROR_INVALID_OP_WHILE_LOG_ENABLED
This operation is not valid while LAN event
logging is enabled.
#define VTEX10XXA_ERROR_PPS_REQUIRES_DIO0_OUTPUT_LOW
PPS enable requires DIO0 output to be enabled
and low.
#define VTEX10XXA_ERROR_GAIN_OUT_OF_RANGE
Linear correction gain value out of range.
#define VTEX10XXA_ERROR_OFFSET_OUT_OF_RANGE
Linear correction offset value out of range.
#define VTEX10XXA_ERROR_INVALID_CORRECTION_LIST_LENGTH
Linear correction list length must be the same as
channel list length.
#define VTEX10XXA_ERROR_INVALID_GAIN_LIST_LENGTH
Gain list length must be the same as channel list
length.
#define VTEX10XXA_ERROR_OPERATION_VALID_ONLY_ON_VOLT_CH
This operation is only valid on general purpose
voltage channels.
#define VTEX10XXA_ERROR_INVALID_EVENTLOG_OVERFLOWMODE
Invalid event log overflow mode.
#define VTEX10XXA_ERROR_INVALID_CAL_FILE_TYPE
Invalid calibration file type.
#define VTEX10XXA_ERROR_ACQUISITION_IN_PROGRESS
#define VTEX10XXA_ERROR_FACTORY_MODE_ONLY
Only works when calFileType parameter is a
value greater than 0.
#define VTEX10XXA_ERROR_CAL_FILE_TOO_LARGE
Unable to load the entire calibration file into
memory.
To Next Page
Loading...
