WABECO D2000 - Tailstock

89 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

60

15. Drawings and legends

15.9 Tailstock

Table of Contents

Default Chapter3
- Default Chapter3
  - Table of Contents3
- Declaration of Conformity for D20006
- Declaration of Conformity for D24007
- Declaration of Conformity for D30008
1 Important Safety Notes9
- Intended Use9
- Improper and Incorrect Use9
- Modifications to the Machine9
- Safety Regulations for Proper Use9
- Safety Features12
- Explanations of the Symbols12
2 Delivery and Set up13
- Transporting the Machine14
3 Putting into Operation15
4 Specifications Regarding the Machine15
- Identification of the Model15
- Noise Emission Declaration for D200015
  - Technical Data D200016
  - Dimensions of D200017
- Noise Emission Declaration for D240017
  - Technical Data D240018
  - Dimensions of D240019
- Noise Emission Declaration for D300019
  - Technical Data D300020
  - Dimensions of D300021
- Revolution Selection21
- Diagram for Reading off the Revolutions22
- Revolution Changer22
- Electrical Equipment23
- Achieving Optimum Results and Avoiding Incorrect Usage24
6 Thread Cutting and Automatic Feed26
- Thread Cutting26
- Use of Change Gears27
- Lefthand Thread31
7 Maintenance32
8 Lubrication of the Machine32
9 Readjusting the Main Spindle33
10 Readjusting the Tool Skid34
11 Tailstock35
12 And 4 Jaw Lathe Chuck36
13 Operational Faults and the Elimination of such37
14 Operating Elements40
- D2000 und D2400 Lathes40
- D3000 Lathes41
15 Drawings and Legends42
- Headstock42
- Foundation with Motor and Cover Cap for D2000/D240044
- Foundation with Motor and Cover Cap for D300046
- Change Gear Quadrant for D2000/D2400/D300048
- Transmission und Lead Screw Drive for D2000/D2400/D300050
- Lead Screw Engine for D300054
- Tool Skid - Longitudinal Skid56
- Tool Skid - Transverse Skid58
- Tailstock60
- Rear Bearing with Guide Rods for D2000/D240062
- Rear Bearing with Guide Rods for D300064
16 Circuit Diagram66
- For D2000/D240066
- For D300067
- Key for Circuit Diagram68
17 Shavings Tank with Spray Protection Wall (Optional)69
- Setting up the Shavings Tank with Spray Protection Wall69
- Mounting the Shavings Tank with Spray Protection Wall on the70
- Drawing and Legend71
18 Coolant System (Optional)72
- Setting up the Coolant System72
- Mounting of the Coolant System to the73
- Safety Regulations for the Handling of Cooling Lubricant74
- Filling the Coolant System75
- Operating the Coolant System75
- Positioning the Segmented Coolant Hose76
- Controlling the Flow of Coolant Using the Coolant Shut-Off Valve76
- Drawing and Legend77
19 Fixed Bezel79
- Operating the Fixed Bezel79
- Drawing and Legend80
20 Moving Bezel81
- Operating the Moving Bezel81
- Drawing and Legend82
21 Tensioning Bracket with Milling Machine Table (Optional)83
- Mounting the Tensioning Bracket with Milling Machine Table to the Lathe83
- Operating Elements85
- Feed Motion of the Milling Machine Table85
- Adjustment of the Dovetail Guide86
- Alignment of the Milling Machine Table86
- Lubrication of the Tensioning Bracket with Milling Machine Table86
- Drawing and Legend87
22 Collet Chuck (Optional)88
- Mounting the Collect Chuck88
- Drawing and Legend88
- Installation and Removal of Collets89

Related product manuals

Preview: WABECO D2000E

Preview: WABECO D2400

Preview: WABECO D6000