WABECO D2000 - Page 65

To Next Page

To Previous Page

15. Drawings and legends

15.11 Rear bearing with guide rods for D3000

Part No. Items Order No. Description

1 1 51003830-0004 Guide rod (940mm)

2 1 51003830-0003 Guide rod (1070mm)

3 1 51400307 Cover sheet

4 4 16191200004010 Screw

5 2 51502518 Lubrication nipple

6 1 51003002-0002 Rear bearing

7 1 51502401-0002 Bevel gear

8 3 16073430003018 Spiral tensioning pin

9 1 51502401-0003 Bevel gear

10 1 51400301-0001 Protective hood

11 2 16193300008020 Screw

12 2 16112500008001 Washer

13 1 51004012-0007 Shaft

14 1 51502003 Spring

15 1 51502131 Ball

16 1 16147100025000 Secure ring

51507022-0001

Ball crank

18 1 51004025-0009 Adjusting ring

19 1 16073430003024 Spiral tensioning pin

20 1 51006731-00022 Scale ring

51400281-0003

Feed spindle

Main Page

Default Chapter3
- Default Chapter3
  - Table of Contents3
- Declaration of Conformity for D20006
- Declaration of Conformity for D24007
- Declaration of Conformity for D30008
1 Important Safety Notes9
- Intended Use9
- Improper and Incorrect Use9
- Modifications to the Machine9
- Safety Regulations for Proper Use9
- Safety Features12
- Explanations of the Symbols12
2 Delivery and Set up13
- Transporting the Machine14
3 Putting into Operation15
4 Specifications Regarding the Machine15
- Identification of the Model15
- Noise Emission Declaration for D200015
  - Technical Data D200016
  - Dimensions of D200017
- Noise Emission Declaration for D240017
  - Technical Data D240018
  - Dimensions of D240019
- Noise Emission Declaration for D300019
  - Technical Data D300020
  - Dimensions of D300021
- Revolution Selection21
- Diagram for Reading off the Revolutions22
- Revolution Changer22
- Electrical Equipment23
- Achieving Optimum Results and Avoiding Incorrect Usage24
6 Thread Cutting and Automatic Feed26
- Thread Cutting26
- Use of Change Gears27
- Lefthand Thread31
7 Maintenance32
8 Lubrication of the Machine32
9 Readjusting the Main Spindle33
10 Readjusting the Tool Skid34
11 Tailstock35
12 And 4 Jaw Lathe Chuck36
13 Operational Faults and the Elimination of such37
14 Operating Elements40
- D2000 und D2400 Lathes40
- D3000 Lathes41
15 Drawings and Legends42
- Headstock42
- Foundation with Motor and Cover Cap for D2000/D240044
- Foundation with Motor and Cover Cap for D300046
- Change Gear Quadrant for D2000/D2400/D300048
- Transmission und Lead Screw Drive for D2000/D2400/D300050
- Lead Screw Engine for D300054
- Tool Skid - Longitudinal Skid56
- Tool Skid - Transverse Skid58
- Tailstock60
- Rear Bearing with Guide Rods for D2000/D240062
- Rear Bearing with Guide Rods for D300064
16 Circuit Diagram66
- For D2000/D240066
- For D300067
- Key for Circuit Diagram68
17 Shavings Tank with Spray Protection Wall (Optional)69
- Setting up the Shavings Tank with Spray Protection Wall69
- Mounting the Shavings Tank with Spray Protection Wall on the70
- Drawing and Legend71
18 Coolant System (Optional)72
- Setting up the Coolant System72
- Mounting of the Coolant System to the73
- Safety Regulations for the Handling of Cooling Lubricant74
- Filling the Coolant System75
- Operating the Coolant System75
- Positioning the Segmented Coolant Hose76
- Controlling the Flow of Coolant Using the Coolant Shut-Off Valve76
- Drawing and Legend77
19 Fixed Bezel79
- Operating the Fixed Bezel79
- Drawing and Legend80
20 Moving Bezel81
- Operating the Moving Bezel81
- Drawing and Legend82
21 Tensioning Bracket with Milling Machine Table (Optional)83
- Mounting the Tensioning Bracket with Milling Machine Table to the Lathe83
- Operating Elements85
- Feed Motion of the Milling Machine Table85
- Adjustment of the Dovetail Guide86
- Alignment of the Milling Machine Table86
- Lubrication of the Tensioning Bracket with Milling Machine Table86
- Drawing and Legend87
22 Collet Chuck (Optional)88
- Mounting the Collect Chuck88
- Drawing and Legend88
- Installation and Removal of Collets89

WABECO D2000 - Page 65

Table of Contents

Related product manuals