Disclaimers
Caution: The CMC is designed to be used as directed. Any use other than that described within the documentation is Caution: The CMC is designed to be used as directed. Any use other than that described within the documentation is
not supported and potentially harmful to the operator. not supported and potentially harmful to the operator.
Caution: The CMC should not be operated when operator is fatigued, under the inuence of alcohol or narcotics, or Caution: The CMC should not be operated when operator is fatigued, under the inuence of alcohol or narcotics, or
other medication where operating heavy machinery warnings are provided. other medication where operating heavy machinery warnings are provided.
Caution: Due to the size and weight of the CMC, two people must perform identied installation operations. Noted Caution: Due to the size and weight of the CMC, two people must perform identied installation operations. Noted
operations performed by a single person may result in injury.operations performed by a single person may result in injury.
Caution: The CMC contains moving parts that may cause injury if not operated in accordance with the instructions. Caution: The CMC contains moving parts that may cause injury if not operated in accordance with the instructions.
Only trained operators should operate machinery. Operators should not touch the CMC while it is cutting a mat. Only trained operators should operate machinery. Operators should not touch the CMC while it is cutting a mat.
Warning: Blades used within the CMC are sharp and will cause injury if not disposed of properly. Blades must be Warning: Blades used within the CMC are sharp and will cause injury if not disposed of properly. Blades must be
disposed of in an appropriate sharps disposal container. disposed of in an appropriate sharps disposal container.
Warning: Hazardous voltages exist within the ECU. No user serviceable parts are located inside the ECU. Opening of Warning: Hazardous voltages exist within the ECU. No user serviceable parts are located inside the ECU. Opening of
the ECU is prohibited. the ECU is prohibited.
Warning: Do not turn on ECU if board cable is disconnected on either end. Risk of electrical shock is present through Warning: Do not turn on ECU if board cable is disconnected on either end. Risk of electrical shock is present through
the ECU plug or non-terminated board cable. the ECU plug or non-terminated board cable.
© 2003, 2021 by Wizard International, Inc. © 2003, 2021 by Wizard International, Inc.
Documentation is provided “as is” and all express or implied conditions, representations, and warranties, including any Documentation is provided “as is” and all express or implied conditions, representations, and warranties, including any
implied warranty of merchantability, tness for a particular purpose or non-infringement, are disclaimed, except to the implied warranty of merchantability, tness for a particular purpose or non-infringement, are disclaimed, except to the
extent that such disclaimers are held to be legally invalid. extent that such disclaimers are held to be legally invalid.
No part of this publication may be reproduced or transmitted in any form or for any purpose without the express No part of this publication may be reproduced or transmitted in any form or for any purpose without the express
permission of Wizard International. The information contained herein may be changed without prior notice.permission of Wizard International. The information contained herein may be changed without prior notice.
Adobe, the Adobe logo, Acrobat, PostScript, and Reader are either trademarks or registered trademarks of Adobe Adobe, the Adobe logo, Acrobat, PostScript, and Reader are either trademarks or registered trademarks of Adobe
Systems Incorporated in the United States and/or other countries.Systems Incorporated in the United States and/or other countries.
Business Objects, Crystal Reports, and other Business Objects products are trademarks or registered trademarks of Business Objects, Crystal Reports, and other Business Objects products are trademarks or registered trademarks of
Business Objects S.A. in the United States and in other countries.Business Objects S.A. in the United States and in other countries.
Canon®, PowerShot™ and Rebel EOS® are trademarks or registered trademark of Canon Inc. in the United States and/Canon®, PowerShot™ and Rebel EOS® are trademarks or registered trademark of Canon Inc. in the United States and/
or other countries. or other countries.
DXF™ is a trademark of Autodesk, Inc., and/or its subsidiaries and/or aliates in the United States and/or other countries.DXF™ is a trademark of Autodesk, Inc., and/or its subsidiaries and/or aliates in the United States and/or other countries.
Microsoft®, Excel®, SQL Server®, Windows®, Windows Vista® and the Windows Vista logo are trademarks or registered Microsoft®, Excel®, SQL Server®, Windows®, Windows Vista® and the Windows Vista logo are trademarks or registered
trademarks of Microsoft Corporation in the United States and/or other countries.trademarks of Microsoft Corporation in the United States and/or other countries.
Visual CADD is a trademark of Numera Software Corporation. Visual CADD is a trademark of Numera Software Corporation.
TrueType is a registered trademark of Apple Computer, Inc. TrueType is a registered trademark of Apple Computer, Inc.
Wizard™, MatDesigner™, FrameShop™,Virtual Gallery®, SwitchBlade Technology™, the Wizard logo, MatDesigner logo, Wizard™, MatDesigner™, FrameShop™,Virtual Gallery®, SwitchBlade Technology™, the Wizard logo, MatDesigner logo,
FrameShop logo and Integrated Framer logo are trademarks or registered trademarks of Wizard International, Inc. in the FrameShop logo and Integrated Framer logo are trademarks or registered trademarks of Wizard International, Inc. in the
United States and/or other countries. United States and/or other countries.
All other corporate and product names and trademarks mentioned in this manual are the property of their respective All other corporate and product names and trademarks mentioned in this manual are the property of their respective
owners. owners.
34
20-36070-1 GettingStartedManualZ1FrameShop
04/07/21
Wizard™ CMC Model Z1 Hardware and Software Getting Started Guide
To Previous Page
Loading...
Need help?
General