Safety
INSPEcnQN
..--
"'--
"'--
"'--
"'--
"'--
"'--
'"
Perform a pre-operation inspection
and functional tests at the beginning
of
each
work
shift.
Perform
the
pre-operation
inspection
first.
DO
NOT
perform the pre-operation
inspection
with
the
engine
running
or
hot.
Contact with
moving
or
heated parts can cause
injury
or
death.
"""'COON
Perform the pre-operation inspection
~
and
functional
tests in an open area.
&:
Inspections and functional tests may
"'--
require assistance. Keep the assis-
:;--
tant
visible
and a safe distance from
the vehicle
to
prevent
injury
or
death.
Become
familiar
with all safety and
hazard decals, regulations, and pro-
cedures. Make
sure
all
proper
safety
and hazard decals are attached
to
the
~=!.=.!Jvehicle
and remain legible.
A
A
brief
description
of
controls, indica-
tors, and instruments is provided
as
a
convenience
for
the operator. These
descriptions
DO
NOT
provide
com-
plete operation
instructions.
Read
and understand the entire manual
to
prevent
equipment
damage, injury,
or
death.
~
"Keep
fingers and feet away
'\\
from
moving parts
or
pinch
~
points
to
prevent
pinching
~,
or
crushing.
DO
NOT
allow
anyone between the tires
and the vehicle frame
while
operating the vehi-
cle.
a
WAR
•
Always
check the
condition
of
the
~
seat
belt
and
mounting
hardware
before operating the vehicle. If the
seat belt
or
mounting
hardware is
defective,
it
may
not
properly restrain
the operator, resulting in
injury
or
death.
•
DO
NOT operate the vehicle until the seat belt
or
mounting
hardware
is
replaced,
if
worn
or
damaged.
• The
seat
belt MUST be
worn
while operating
the vehicle. Failure
to
wear the seat belt could
result
in
injury
or
death.
a WARM
Keep
the
Operator
Manual on the
A
vehicle
at all times. Contact Xtreme
Manufacturing
for
any replacement
manuals.
Before Starting Vehicle
O
Wear appropriate protective clothing.
Personal
protective
equipment
can
include,
but
is
not
limited
to
hardhat,
gloves, footwear, safety glasses
or
goggles,
and
hearing
protection.
Make
sure
clothing
is snug and properly belted.
DO
NOT wear loose clothing, jewelry, watches,
or
anything
that
can catch on vehicle controls,
moving
parts, etc.
~
Consult
Material Safety
Data Sheets (MSDS)
for
chemical hazards and
first
aid
instructions.
MSDS
should
be available from
the
manufacturer
or
supplier
of
the fluid.
A
Clearly
define
responsibilities
and
procedures
for
operating the vehicle
and all attachments.
DO
NOT proceed
until
you
seek
expert
assistance
from
a qualified person
if
any
doubt
or
question
arises
about
the
correct
or
safe meth-
ods
for
operating the vehicle.
1111
To
avoid
injury
or
death,
~
::::::
::::: carefully read and under-
-
stand
all
instructions
before operating
the
vehi-
cle.
DO
NOT operate,
mod-
ify, repair,
or
maintain
the
vehicle unless
you
read and understand the
instructions
and warn-
ings in
this
and all
other
applicable manuals and
technical
publications.
Follow
all State and
Federal health and safety laws and/or local regu-
lations.
Xtreme Manufacturing 9
800-497-1704
To Next Page
Loading...
Need help?
General
