Yamaha RX5 - Page 47

3. Press START to enter the level step setting. Оп the LCD the word “step” will briefly
change to “set!” then return to “step”.
* The original level will be retained at key A. Keys B through L will increase or decrease
in level, according to a positive or negative level step setting
NOTE: The Multi Step function cannot alter a voice’s level beyond the upper and lower
limits of its level range (as set by the EDIT VOICE or KEY PARAMETER ASSIGN
functions). If a voice's level is already set at or near these limits, this will result in all keys
to the right of the first key that reaches this limit having the same level.
PARAMETER 3: ATTACK RATE
1. To select Attack, press "3".
multi:Int-BD 1
B step
attack
2. Use the - 1/NO and +4/YES keys or the DATA ENTRY slider to change the attack
step.
Range: + 10.
3. Press START to enter the attack step setting. On the LCD the word "step" will briefly
change to "set!" then return to “step”.
e The origina! Attack Rate setting will be retained at key A. Keys B through L will
increase or decrease in Attack Rate, according to a positive or negative Attack Rate
Step setting.
NOTE: The Multi Step function cannot alter a voice's attack rate beyond the upper and
lower limits of its Attack Rate range (as set by the EDIT VOICE or KEY PARAMETER
ASSIGN functions). If a voice's Attack Rate is already set at or near these limits, this will
result in all keys to the right of the first key that reaches this limit having the same Attack
Rate.
PARAMETER 4: DECAY RATE
1. To select Decay press “4”.
multi:Int-BD 1
@ step
decay
2. Use the —1/NO and +1/YES keys or the DATA ENTRY slider to change the decay
Step.
43
KEY ASSIGN MODE
Range: + 10.
3. Press START to enter the decay step setting. On the LCD the word “step” will briefly
change to “set!” then return to "step".
e The original Decay Rate setting will be retained at key A. Keys B through L will
increase or decrease in Decay Rate, according to a positive or negative Decay Rate
step setting.
NOTE: The Multi Step function cannot alter a voice's decay rate beyond the upper and
lower limits of its Decay Rate range (as set by the EDIT VOICE or KEY PARAMETER
ASSIGN functions). If a voice's Decay Rate is already set at or near these limits, this will
result in all keys to the right of the first key that reaches this limit having the same Decay
Rate.
JOB 704: MULTI STEP
FUNCTION то alter the Multi Step parameters of a voice assigned to
instrument keys А thru L, via the Multi Voice function.
This job carries out exactly the same functions as the Multi Step functions described in
the previous Job, if a voice has ALREADY been assigned to instrument keys A thru L
via the the Multi Voice function. It enables you to make adjustments to Multi Step
parameters that you have already set. Otherwise, if you attempt to alter Multi Step
settings by using Job #03, you will first have to re-assign your selected voice to the
Multi Mode, and this will cancel all previous Multi Step settings.
* Multi Step parameters are memorized when a Pattern is written. You could then
change the parameters and write more notes on the same Pattern — ideal for adding
other sounds or pitches to a Pattern.
NOTE: This Job can NOT be selected if a voice has not first been assigned to the Multi |
Моде.
OPERATION
1. After assigning a voice to the Multi Mode, press KEY ASSIGN and select JOB #04.
The LCD wilt show the last Multi Step parameter that was selected.
2. Multi Step parameters can be selected and re-edited. Refer to Job #03 for operation
details.
JOB #05: ACCENT LEVELS
FUNCTION т program two different level changes to individual voices.
Pressing any instrument key while holding either of the green
ACCENT keys causes that instrument to sound at its ACCENT
1 оғ ACCENT 2 level.
The accent level range is the same as the voice ievel range (refer to EDIT VOICE JOB
#05). The accent level setting is ADDED to the voice level setting to produce the actual
accent level. Negative accent levels can also be set, for interesting effects