Deceleration Time 2 .............................. 225
Digital Operator Display Selection ................. 241
DIP Switch S1......................................67
Down Command ................................. 232
d References ..................................... 228
Drive/kVA Selection.............................. 242
Drive Baseblock .................................. 135
Drive Capacity Setting Fault....................... 152
Drive Capacity Signal Fault ...................134, 139
Drive Cooling Fans ............................... 174
Drive Dedicated Motor (Constant Torque, 1:10)..... 115
Drive Mode .................................85, 86, 87
Drive Motor Overload Protection .................. 272
Drive Overload ...............................135, 143
Drive Ready...................................... 234
Drive Short-Circuit Rating ........................ 271
Drive Slave Address .............................. 235
Drive Status Monitors............................. 118
Drive Transmit Wait Time......................... 236
Drive Unit Setting Error........................... 136
Drive Watt Loss Data ............................. 217
During Baseblock................................. 234
During Run ...................................... 233
Dynamic Braking Resistor......................... 135
E
E1-01 ............................................ 230
E1-03 ............................................ 230
E1-04 .............................. 160, 161, 163, 230
E1-06 ........................................161, 230
E1-07 ............................................ 230
E1-08 ........................................131, 158
E1-09 ..........................157, 158, 163, 164, 230
E1-10 ................................... 131, 158, 161
E1 V/f Pattern Characteristics...................... 230
E2-01 .............................. 114, 131, 230, 272
E2-02 ................................... 111, 131, 231
E2-03 ................................... 111, 131, 231
E2-05 ........................................111, 231
E2 Motor Parameters.............................. 230
EEPROM Data Error.............................. 138
EEPROM Write Error.........................134, 140
EF ...........................................135, 148
EF0..........................................134, 139
EF1..........................................139, 148
EF1 to EF5....................................... 135
EF2..........................................139, 149
EF3..........................................139, 149
EF4..........................................139, 149
EF5..........................................139, 149
Electrical Thermal Motor Protection ............... 113
EMC Guidelines.................................. 255
Err...........................................134, 140
European Standards ............................... 255
Excessive Motor Oscillation and Erratic Rotation ... 162
External Digital Operator Connection Fault ......... 144
External Fault ................................140, 149
External Fault (input terminal S1 to S5) ........134, 135
External Fault (user selection possible) ............. 233
External Search Command 1....................... 233
External Search Command 2....................... 233
F
Fast-stop (N.C.) .................................. 232
Fast-Stop (N.O.) .................................. 232
Fast-stop Time ................................... 225
Fault............................................. 234
Fault Causes and Solutions ........................ 137
Fault Detection ................................... 137
Fault Displays .................................... 137
Fault History Example ............................ 154
Fault Reset ....................................... 232
Fault Reset Example .............................. 133
Faults ........................................133, 134
FLASH Memory Fault ............................ 134
Forward/Reverse Run Command Input Error........ 148
Forward Run Command (2-Wire sequence) ......... 233
Fref/Fout Agree 1................................. 233
Frequency (FOUT) Detection 1 .................... 233
Frequency (FOUT) Detection 2 .................... 234
Frequency Reference..........................118, 243
Frequency Reference 1 ........................103, 228
Frequency Reference 2 ........................103, 228
Frequency Reference 3 ........................103, 228
Frequency Reference 4 ........................103, 228
Frequency Reference 5 ............................ 228
Frequency Reference 6 ............................ 228
Frequency Reference 7 ............................ 228
Frequency Reference 8 ............................ 228
Frequency Reference Hold Function Selection ...... 229
Frequency Reference Selection .................... 224
Frequency Reference Selection 1................... 157
Index
YASKAWA ELECTRIC TOEP C710606 25D YASKAWA AC Drive J1000 Installation & Start-Up Manual
279
To Next Page
Loading...
Need help?
General
