YASKAWA CIPR-GA50CB001

YASKAWA SIEPC71061753C GA500 Technical Manual 791
Rating (Single-phase 200 V)
Drive............................................................... 330
Rating (Three-phase 200 V)
Drive............................................................... 331
rdEr..................................................................... 295
Remove
Front cover ........................................................ 43
Keypad ............................................................. 45
RESET key ............................................................ 121
Residual Current Monitor/Residual Current Device
RCM/RCD........................................................ 105
Wiring ............................................................. 105
Restore
Parameters (keypad to drive)................................... 140
Reverse Operation Selection........................................ 507
rF ....................................................................... 274
rH ....................................................................... 274
RJ-45 connector ...................................................... 121
Rotational Auto-Tuning
Induction Motor.................................................. 143
PM motors ........................................................ 144
Precautions ....................................................... 148
rr ........................................................................ 274
Protection Functions ............................................ 735
rUn ..................................................................... 285
Run command
LOCAL/REMOTE Run selection ............................. 504
Switching between LOCAL/REMOTE....................... 504
Run Command at Power Up ........................................ 512
Run Command Selection 2
Switching between LOCAL/REMOTE....................... 511
RUN indicator ........................................................ 121
RUN key............................................................... 121
S
S-curve characteristics
Parameter ......................................................... 551
SC ...................................................................... 274
SCF..................................................................... 274
Screen .................................................................. 137
SE....................................................................... 285
SEr...................................................................... 275
Serial communication terminals
MEMOBUS/Modbus Communications ....................... 94
Short Circuit Braking
Parameter ......................................................... 512
Side-by-side
Derating..................................................... 343, 733
Slip compensation
Parameter ......................................................... 552
Softcharge Relay Maintenance Set................................. 770
Software Current Limit Selection
Protection Functions ............................................ 732
Speed Agreement
Parameter ......................................................... 716
Speed Detection ...................................................... 718
Parameter ......................................................... 716
Speed Estimation Speed Search .................................... 516
Speed Search function
Operation during momentary power loss..................... 702
Parameter ......................................................... 515
Stall Prevention function
Parameter ......................................................... 707
Stationary Auto-Tuning
Induction Motor.................................................. 143
PM motors ........................................................ 144
Precautions ....................................................... 148
Stationary Auto-Tuning for Line-to-Line Resistance............ 143
Precautions ....................................................... 148
Stator resistance Auto-Tuning ...................................... 144
Precautions ....................................................... 148
SToF.................................................................... 285
Stop command
LOCAL/REMOTE Run selection ............................. 504
STOP key.............................................................. 121
STOP Key Function Selection...................................... 764
Stop with Constant Distance..................................578–579
Stopping Method Selection ......................................... 504
STPo ................................................................... 275
Surge protective device
Connection........................................................ 109
T
Temperature
Environment....................................................... 31
Terminal block
Configuration of control circuit terminal block .............. 94
Configuration of main circuit terminal block ................. 65
Control circuit terminal block functions....................... 90
I/O terminals function selection switches ..................... 97
Terminal function selection .......................................... 99
Terminal A2 ................................................... 97, 99
Terminal AM ................................................ 97, 100
Termination resistor
Setting switch .................................................... 100
Test run
Checklist .......................................................... 157
Fine tuning........................................................ 152
Procedure ......................................................... 131
Procedure for no-load test run ................................. 150
Procedure for test run with actual load ....................... 150
Thermal overload relay
Connection........................................................ 106
Tightening torque
Control circuit terminals......................................... 94
Main circuit terminals............................................ 73
TiM
Fault ............................................................... 275
Minor Fault ....................................................... 285
Timer function
Parameter ......................................................... 523
Torque Compensation
Parameter ......................................................... 556
Torque limit function
Parameter ......................................................... 726
Troubleshooting
Code Displayed .................................................. 251
No Code Displayed.............................................. 298
Troubleshooting without Fault Display ........................... 298
TrPC.................................................................... 285
Tuning.................................................................. 546
U
U2, U3 Initialization ................................................. 770
UL3
Fault ............................................................... 275
Minor Fault ....................................................... 285
UL4
Fault ............................................................... 275
Minor Fault ....................................................... 285
UL5
Fault ............................................................... 275
Minor Fault ....................................................... 285
Undertorque detection
Parameter ......................................................... 721
Unit of measurement setting