YASKAWA Varispeed G7 Series

Trial Operation Procedures
4- 11
Set the autotuning type.
Step Digital Operator Display
1 Turn ON the power supply.
2
Press the MENU Key several times to access the autotuning display.
The autotuning display will not appear during operation or when a fault
has occurred.
3
Press the DATA/ENTER Key to display the T1-01 (Autotuning Mode
Selection) user constant setting.
4 Press the DATA/ENTER Key to display the current set value of T1-01.
5 Press the Increment Key and set the value to 0 (rotational autotuning).
6 Press the DATA/ENTER Key to confirm the value.
㻲㼞㼑㼝㼡㼑㼚㼏㼥㻌㻾㼑㼒
㻙㻰㻾㻵㼂㻱㻙
㼁㻝㻙㻜㻞㻩㻌㻌㻜㻚㻜㻜㻴㼦
㼁㻝㻙㻜㻟㻩㻌㻌㻜㻚㻜㻜㻭
㻾㼐㼥
8 +]
Initial display

㻖㻖㻌㻹㼍㼕㼚㻌㻹㼑㼚㼡㻌㻖㻖
㻙㻭㻚㼀㼁㻺㻱㻙
㻭㼡㼠㼛㻙㼀㼡㼚㼕㼚㼓
㼀㼡㼚㼕㼚㼓㻌㻹㼛㼐㼑㻌㻿㼑㼘
㻙㻭㻚㼀㼁㻺㻱㻙
7

㻿㼠㼍㼚㼐㼍㼞㼐㻌㼀㼡㼚㼕㼚㼓
㻎㻜㻎


㼀㼡㼚㼕㼚㼓㻌㻹㼛㼐㼑㻌㻿㼑㼘
㻙㻭㻚㼀㼁㻺㻱㻙
7
㻿㼠㼍㼚㼐㼍㼞㼐㻌㼀㼡㼚㼕㼚㼓
㻎㻜㻎

 
㼀㼡㼚㼕㼚㼓㻌㻹㼛㼐㼑㻌㻿㼑㼘
㻙㻭㻚㼀㼁㻺㻱㻙
7
㻿㼠㼍㼚㼐㼍㼞㼐㻌㼀㼡㼚㼕㼚㼓
㻎㻜㻎

 
㻙㻭㻚㼀㼁㻺㻱㻙
㻱㼚㼠㼞㼥㻌㻭㼏㼏㼑㼜㼠㼑㼐
Display when the setting has been confirmed
Display after the setting has been confirmed
㼀㼡㼚㼕㼚㼓㻌㻹㼛㼐㼑㻌㻿㼑㼘
㻙㻭㻚㼀㼁㻺㻱㻙
7

㻿㼠㼍㼚㼐㼍㼞㼐㻌㼀㼡㼚㼕㼚㼓
㻎㻜㻎


TOE-S616-60.1.book 11 ページ ２０１７年８月４日 金曜日 午後３時４１分