YOKOGAWA DL9040

5-134
IM 701310-17E
:SEARch<x>:SPATtern:LATCh?
Function Queries all settings related to latch of the serial
pattern search.
Syntax
:SEARch<x>:SPATtern:LATCh?
<x> = 1 or 2
Example
:SEARCH1:SPATTERN:LATCH? -> :SEARCH1:
SPATTERN:LATCH:TRACE 1;POLARITY FALL
:SEARch<x>:SPATtern:LATCh:POLarity
Function Sets the polarity of the latch trace of the serial pattern
search or queries the current setting.
Syntax
:SEARch<x>:SPATtern:LATCh:
POLarity {FALL|RISE}
:SEARch<x>:SPATtern:LATCh:POLarity?
<x> = 1 or 2
Example
:SEARCH1:SPATTERN:LATCH:POLARITY FALL
:SEARCH1:SPATTERN:LATCH:POLARITY?
-> :SEARCH1:SPATTERN:LATCH:
POLARITY FALL
Description • This command is valid when
:SEARch<x>:
SPATtern:CLOCk:MODE ON
.
• This command is invalid when
:SEARch<x>:
SPATtern:LATCh:TRACe NONE
.
:SEARch<x>:SPATtern:LATCh:TRACe
Function Sets the latch trace of the serial pattern search or
queries the current setting.
Syntax
:SEARch<x>:SPATtern:LATCh:TRACe {<NRf>|
NONE}
:SEARch<x>:SPATtern:LATCh:TRACe?
<x> = 1 or 2
<NRf> = 1 to 8
Example
:SEARCH1:SPATTERN:LATCH:TRACE 1
:SEARCH1:SPATTERN:LATCH:TRACE?
-> :SEARCH1:SPATTERN:LATCH:TRACE 1
Description This command is valid when
:SEARch<x>:
SPATtern:CLOCk:MODE ON
.
:SEARch<x>:SPATtern:SETup?
Function Queries all settings related to setup of the serial
pattern search.
Syntax
:SEARch<x>:SPATtern:SETup?
<x> = 1 or 2
Example
:SEARCH1:SPATTERN:SETUP? -> :SEARCH1:
SPATTERN:SETUP:BITRATE 1.000E+03;DATA:
ACTIVE HIGH;TRACE 1;:SEARCH1:SPATTERN:
SETUP:PATTERN "1100"
:SEARch<x>:SPATtern:CLOCk:MODE
Function Enables/Disables the clock of the serial pattern
search or queries the current setting.
Syntax
:SEARch<x>:SPATtern:CLOCk:
MODE {<Boolean>}
:SEARch<x>:SPATtern:CLOCk:MODE?
<x> = 1 or 2
Example
:SEARCH1:SPATTERN:CLOCK:MODE ON
:SEARCH1:SPATTERN:CLOCK:MODE?
-> :SEARCH1:SPATTERN:CLOCK:MODE 1
:SEARch<x>:SPATtern:CLOCk:POLarity
Function Sets the polarity of the clock trace of the serial pattern
search or queries the current setting.
Syntax
:SEARch<x>:SPATtern:CLOCk:
POLarity {FALL|RISE}
:SEARch<x>:SPATtern:CLOCk:POLarity?
<x> = 1 or 2
Example
:SEARCH1:SPATTERN:CLOCK:POLARITY FALL
:SEARCH1:SPATTERN:CLOCK:POLARITY?
-> :SEARCH1:SPATTERN:CLOCK:
POLARITY FALL
Description This command is valid when
:SEARch<x>:
SPATtern:CLOCk:MODE ON
.
:SEARch<x>:SPATtern:CLOCk:SOURce
Function Sets the clock trace of the serial pattern search or
queries the current setting.
Syntax
:SEARch<x>:SPATtern:CLOCk:
SOURce {<NRf>}
:SEARch<x>:SPATtern:CLOCk:SOURce?
<x> = 1 or 2
<NRf> = 1 to 8
Example
:SEARCH1:SPATTERN:CLOCK:SOURCE 1
:SEARCH1:SPATTERN:CLOCK:SOURCE?
-> :SEARCH1:SPATTERN:CLOCK:SOURCE 1
Description This command is valid when
:SEARch<x>:
SPATtern:CLOCk:MODE ON
.
:SEARch<x>:SPATtern:CS
Function Enables/Disables the chip select of the serial pattern
search or queries the current setting.
Syntax
:SEARch<x>:SPATtern:CS {<Boolean>}
:SEARch<x>:SPATtern:CS?
<x> = 1 or 2
Example
:SEARCH1:SPATTERN:CS ON
:SEARCH1:SPATTERN:CS? -> :SEARCH1:
SPATTERN:CS 1
Description This command is valid when
:SEARch<x>:
SPATtern:CLOCk:MODE ON
.
5.20 SEARch Group