YOKOGAWA DL9040

5-135
IM 701310-17E
Commands
1
2
3
4
5
6
App
Index
:SEARch<x>:SPATtern[:SETup]:HEXA
Function Sets the pattern of the serial pattern search in
hexadecimal notation.
Syntax
:SEARch<x>:SPATtern[:SETup]:HEXA
{<String>}
<x> = 1 or 2
<String> = Up to 32 characters by combining ‘0’
to ‘F’
and ‘X’
Example
:SEARCH1:SPATTERN:SETUP:HEXA "ABCD"
:SEARch<x>:SPATtern[:SETup]:PATTern
Function Sets the pattern of the serial pattern search in binary
notation or queries the current setting.
Syntax
:SEARch<x>:SPATtern[:SETup]:
PATTern {<String>}
:SEARch<x>:SPATtern[:SETup]:PATTern?
<x> = 1 or 2
<String> = Up to 128 characters by combining ‘0’, ‘1’,
and ‘X’
Example
:SEARCH1:SPATTERN:SETUP:
PATTERN "1100110111101111"
:SEARCH1:SPATTERN:SETUP:PATTERN?
-> :SEARCH1:SPATTERN:SETUP:
PATTERN "1100110111101111"
:SEARch<x>:SPOint
Function Sets the search start position or queries the current
setting.
Syntax
:SEARch<x>:SPOint {<NRf>}
:SEARch<x>:SPOint?
<x> = 1 or 2
<NRf> = –5 to 5 (div)
Example
:SEARCH1:SPOINT 1
:SEARCH1:SPOINT?
-> :SEARCH1:SPOINT 1.000E+00
:SEARch<x>:STRace
Function Sets the search source trace or queries the current
setting.
Syntax
:SEARch<x>:STRace {<NRf>}
:SEARch<x>:STRace?
<x> = 1 or 2
<NRf> = 1 to 8
Example
:SEARCH1:STRACE 1
:SEARCH1:STRACE? -> :SEARCH1:STRACE 1
Description • This command is valid when
:SEARch<x>:TYPE
EDGE|EQUalify
.
• This command is valid when
:SEARch<x>:
TYPE WIDTh
and
:SEARch<x>:WIDTh:TYPE
PQUalify|PULSe
.
:SEARch<x>:SPATtern[:SETup]:BITRate
Function Sets the bit rate of the serial pattern search or queries
the current setting.
Syntax
:SEARch<x>:SPATtern[:SETup]:
BITRate {<NRf>}
:SEARch<x>:SPATtern[:SETup]:BITRate?
<x> = 1 or 2
<NRf> = 1 to 1G (bps)
Example
:SEARCH1:SPATTERN:SETUP:BITRATE 1
:SEARCH1:SPATTERN:SETUP:BITRATE?
-> :SEARCH1:SPATTERN:SETUP:
BITRATE 1.000E+00
Description This command is valid when
:SEARch<x>:
SPATtern:CLOCk:MODE OFF
.
:SEARch<x>:SPATtern[:SETup]:CLEar
Function Clears the entire pattern of the serial pattern search
(to don’t care).
Syntax
:SEARch<x>:SPATtern[:SETup]:CLEar
<x> = 1 or 2
Example
:SEARCH1:SPATTERN:SETUP:CLEAR
:SEARch<x>:SPATtern[:SETup]:DATA?
Function Queries all settings related to data of the serial
pattern search.
Syntax
:SEARch<x>:SPATtern[:SETup]:DATA?
<x> = 1 or 2
Example
:SEARCH1:SPATTERN:SETUP:DATA?
-> :SEARCH1:SPATTERN:SETUP:DATA:
ACTIVE HIGH;TRACE 1
:SEARch<x>:SPATtern[:SETup]:DATA:
ACTive
Function Sets the active level of the data trace of the serial
pattern search or queries the current setting.
Syntax
:SEARch<x>:SPATtern[:SETup]:DATA:
ACTive {HIGH|LOW}
:SEARch<x>:SPATtern[:SETup]:DATA:
ACTive?
<x> = 1 or 2
Example
:SEARCH1:SPATTERN:SETUP:DATA:
ACTIVE HIGH
:SEARCH1:SPATTERN:SETUP:DATA:ACTIVE?
-> :SEARCH1:SPATTERN:SETUP:DATA:
ACTIVE HIGH
:SEARch<x>:SPATtern[:SETup]:DATA:TRACe
Function Sets the data trace of the serial pattern search or
queries the current setting.
Syntax
:SEARch<x>:SPATtern[:SETup]:DATA:
TRACe {<NRf>}
:SEARch<x>:SPATtern[:SETup]:DATA:TRACe?
<x> = 1 or 2
<NRf> = 1 to 8
Example
:SEARCH1:SPATTERN:SETUP:DATA:TRACE 1
:SEARCH1:SPATTERN:SETUP:DATA:TRACE?
-> :SEARCH1:SPATTERN:SETUP:DATA:TRACE 1
5.20 SEARch Group