5-133
IM 701310-17E
Commands
:SEARch<x>:EXECute
Function Executes the search. This is an overlap command.
Syntax
:SEARch<x>:EXECute
<x> = 1 or 2
Example
:SEARCH1:EXECUTE
:SEARch<x>:HOLDoff
Function Sets the hold off detection or queries the current
setting.
Syntax
:SEARch<x>:HOLDoff {<Time>}
:SEARch<x>:HOLDoff?
<x> = 1 or 2
<T
ime> = 0 s to 1 s in 100-ps steps
Example
:SEARCH1:HOLDOFF 0S
:SEARCH1:HOLDOFF? -> :SEARCH1:
HOLDOFF 0.000E+00
:SEARch<x>:LOGic
Function Sets the search logic or queries the current setting.
Syntax
:SEARch<x>:LOGic {AND|OR}
:SEARch<x>:LOGic?
<x> = 1 or 2
Example
:SEARCH1:LOGIC OR
:SEARCH1:LOGIC? -> :SEARCH1:LOGIC OR
Description • This command is valid when
:SEARch<x>:TYPE
EQUalify|SPATtern|STATe.
• This command is valid when
:SEARch<x>:
TYPE WIDTh
and
:SEARch<x>:WIDTh:TYPE
PQUalify|PSTAte.
:SEARch<x>:POLarity
Function Sets the search polarity or queries the current setting.
Syntax
:SEARch<x>:POLarity {ENTer|EXIT|FALL|
FALSe|NEGative|POSitive|RISE|
TRUE}
:SEARch<x>:POLarity?
<x> = 1 or 2
Example
:SEARCH1:POLARITY ENTER
:SEARCH1:POLARITY? -> :SEARCH1:
POLARITY ENTER
Description • {F
ALL|RISE} is valid when
:SEARch<x>:TYPE
EDGE|EQUalify.
• {ENTer|EXIT} is valid when
:SEARch<x>:TYPE
STATe
.
• {NEGative|POSitive} is valid when
:SEARch<x>:
TYPE WIDTh
and
:SEARch<x>:WIDTh:TYPE
PQUalify|PULSe
.
• {FALSe|TRUE} is valid when
:SEARch<x>:TYPE
WIDTh
and
:SEARch<x>:WIDTh:TYPE PSTAte
.
:SEARch<x>:SELect
Function Sets the detection waveform number of the search
function and queries the position that corresponds to
the detection waveform number.
Syntax
:SEARch<x>:SELect {<NRf>|MAXimum}
:SEARch<x>:SELect?
<x> = 1 or 2
<NRf> = 0 to 4999
Example
:SEARCH1:SELECT 1
:SEARCH1:SELECT? -> :SEARCH1:
SELECT 1.500E+00
Description If there is no searched position, “NAN” is returned for
the query.
:SEARch<x>:SELect? MAXimum
Function Queries the detection count of the search function.
Syntax
:SEARch<x>:SELect? {MAXimum}
<x> = 1 or 2
Example
:SEARCH1:SEECT? MAXIMUM -> :SEARCH1:
SELECT 100
Description If there is no searched position, “NAN” is returned for
the query.
:SEARch<x>:SMODe
Function Sets the skip mode or queries the current setting.
Syntax
:SEARch<x>:SMODe {DECimation|HOLDoff|
OFF}
:SEARch<x>:SMODe?
<x> = 1 or 2
Example
:SEARCH1:SMODE HOLDOFF
:SEARCH1:SMODE? -> :SEARCH1:
SMODE HOLDOFF
:SEARch<x>:SPATtern? (Serial Pattern)
Function Queries all settings related to the serial pattern
search.
Syntax
:SEARch<x>:SPATtern?
<x> = 1 or 2
Example
:SEARCH1:SPATTERN? -> :SEARCH1:
SPATTERN:CLOCK:MODE 1;POLARITY FALL;
SOURCE 1;:SEARCH1:SPATTERN:CS 1;LATCH:
TRACE 1;POLARITY FALL;:SEARCH1:
SPATTERN:SETUP:BITRATE 1.000E+00;
PATTERN "1100110111101111"
:SEARch<x>:SPATtern:CLOCk?
Function Queries all settings related to clock of the serial
pattern search.
Syntax
:SEARch<x>:SPATtern:CLOCk?
<x> = 1 or 2
Example
:SEARCH1:SPATTERN:CLOCK? -> :SEARCH1:
SPATTERN:CLOCK:MODE 1;
POLARITY FALL;SOURCE 1
5.20 SEARch Group
To Next Page
Loading...
