YOKOGAWA DL9040

5-195
IM 701310-17E
Commands
1
2
3
4
5
6
App
Index
:TRIGger:ENHanced:TV:USERdefine:
DEFinition
Function Sets the user-defined resolution or queries the
current setting.
Syntax
:TRIGger:ENHanced:TV:USERdefine:
DEFinition {HD|SD}
:TRIGger:ENHanced:TV:USERdefine:
DEFinition?
Example
:TRIGGER:ENHANCED:TV:USERDEFINE:
DEFINITION HD
:TRIGGER:ENHANCED:TV:USERDEFINE:
DEFINITION? -> :TRIGGER:ENHANCED:TV:
USERDEFINE:DEFINITION HD
:TRIGger:ENHanced:TV:USERdefine:
HFRejection (HighFrequencyREJECTION)
Function Sets the user-defined low pass filter (HF rejection) or
queries the current setting.
Syntax
:TRIGger:ENHanced:TV:USERdefine:
HFRejection {<Frequency>|OFF}
:TRIGger:ENHanced:TV:USERdefine:
HFRejection?
<Frequency> = 300kHz
Example
:TRIGGER:ENHANCED:TV:USERDEFINE:
HFREJECTION OFF
:TRIGGER:ENHANCED:TV:USERDEFINE:
HFREJECTION? -> :TRIGGER:ENHANCED:TV:
USERDEFINE:HFREJECTION OFF
:TRIGger:ENHanced:TV:USERdefine:
HSYNc (Hsync Freq)
Function Sets the user-defined horizontal sync signal or
queries the current setting.
Syntax
:TRIGger:ENHanced:TV:USERdefine:
HSYNc {<Frequency>}
:TRIGger:ENHanced:TV:USERdefine:HSYNc?
<Frequency> = 10k to 200k (Hz)
Example
:TRIGGER:ENHANCED:TV:USERDEFINE:
HSYNC 10KHZ
:TRIGGER:ENHANCED:TV:USERDEFINE:HSYNC?
-> :TRIGGER:ENHANCED:TV:USERDEFINE:
HSYNC 10.00E+03
:TRIGger:ENHanced:UART?
Function Queries all settings related to the UART signal trigger.
Syntax
:TRIGger:ENHanced:UART?
Example
:TRIGGER:ENHANCED:UART? -> :TRIGGER:
ENHANCED:UART:BRATE 19200;
FORMAT BIT7PARITY;POLARITY NEGATIVE;
SOURCE 1;SPOINT 18.8E+00
:TRIGger:ENHanced:UART:BRATe
Function Sets the UART signal trigger bit rate (data transfer
rate) or queries the current setting.
Syntax
:TRIGger:ENHanced:UART:
BRATe {<NRf>|USER, <NRf>}
:TRIGger:ENHanced:UART:BRATe?
<NRf> = 1200, 2400, 4800, 9600, 19200, 38400,
57600, 115200
<NRf> of USER = See the DL9040/DL9140/DL9240
User's Manual
Example
:TRIGGER:ENHANCED:UART:BRATE 19200
:TRIGGER:ENHANCED:UART:BRATE? ->
:TRIGGER:ENHANCED:UART:BRATE 19200
:TRIGger:ENHanced:UART:FORMat
Function Sets the UART signal trigger format or queries the
current setting.
Syntax
:TRIGger:ENHanced:UART:
FORMat {BIT7parity|BIT8Noparity|
BIT8Parity}
:TRIGger:ENHanced:UART:FORMat?
Example
:TRIGGER:ENHANCED:UART:
FORMAT BIT7PARITY
:TRIGGER:ENHANCED:UART:FORMAT? ->
:TRIGGER:ENHANCED:UART:
FORMAT BIT7PARITY
:TRIGger:ENHanced:UART:POLarity
Function Sets the UART signal trigger polarity or queries the
current setting.
Syntax
:TRIGger:ENHanced:UART:
POLarity {NEGative|POSitive}
:TRIGger:ENHanced:UART:POLarity?
Example
:TRIGGER:ENHANCED:UART:
POLARITY NEGATIVE
:TRIGGER:ENHANCED:UART:POLARITY? ->
:TRIGGER:ENHANCED:UART:
POLARITY NEGATIVE
:TRIGger:ENHanced:UART:SOURce
Function Sets the UART signal trigger source or queries the
current setting.
Syntax
:TRIGger:ENHanced:UART:SOURce {<NRf>}
:TRIGger:ENHanced:UART:SOURce?
<NRf> = 1 to 4
Example
:TRIGGER:ENHANCED:UART:SOURCE 1
:TRIGGER:ENHANCED:UART:SOURCE? ->
:TRIGGER:ENHANCED:UART:SOURCE 1
:TRIGger:ENHanced:UART:SPOint
Function Sets the UART signal trigger sample point or queries
the current setting.
Syntax
:TRIGger:ENHanced:UART:SPOint {<NRf>}
:TRIGger:ENHanced:UART:SPOint?
<NRf> = 18.8 to 90.6(%)
Example
:TRIGGER:ENHANCED:UART:SPOINT 18.8
:TRIGGER:ENHANCED:UART:SPOINT? ->
:TRIGGER:ENHANCED:UART:SPOINT 18.8E+00
5.29 TRIGger Group