YOKOGAWA DLM2000 Series - Page 127

5-94
IM 710105-17E
:FFT<x>:MEASure?
Function Queries all automatic measurement settings for
FFT analysis.
Syntax
:FFT<x>:MEASure?
<x> = 1 or 2 (1 only for 2-channel models)
:FFT<x>:MEASure:MARKer?
Function Queries all marker cursor measurement settings
for FFT analysis.
Syntax
:FFT<x>:MEASure:MARKer?
<x> = 1 or 2 (1 only for 2-channel models)
:FFT<x>:MEASure:MARKer[:BASic]?
Function Queries all Basic marker cursor item settings for
FFT analysis.
Syntax
:FFT<x>:MEASure:MARKer:BASic?
<x> = 1 or 2 (1 only for 2-channel models)
:FFT<x>:MEASure:MARKer[:BASic]:ALL
Function Collectively turns on or off all Basic marker cursor
items for FFT analysis.
Syntax
:FFT<x>:MEASure:MARKer[:BASic]:A
LL {<Boolean>}
<x> = 1 or 2 (1 only for 2-channel models)
Example
:FFT1:MEASURE:MARKER:BASIC:ALL ON
:FFT<x>:MEASure:MARKer[:BASic]:DFReq
uency?
Function Queries all of the settings for frequency
measurement between marker cursors for FFT
analysis.
Syntax
:FFT<x>:MEASure:MARKer[:BASic]:DFRequ
ency?
<x> = 1 or 2 (1 only for 2-channel models)
:FFT<x>:MEASure:MARKer[:BASic]:DFReq
uency:STATe
Function Sets or queries the on/off status of the frequency
measured between marker cursors for FFT
analysis.
Syntax
:FFT<x>:MEASure:MARKer[:BASic]:DFRequ
ency:STATe {<Boolean>}
:FFT<x>:MEASure:MARKer[:BASic]:DFRequ
ency:STATe?
<x> = 1 or 2 (1 only for 2-channel models)
Example
:FFT1:MEASURE:MARKER:BASIC:
DFREQUENCY:STATE ON
:FFT1:MEASURE:MARKER:BASIC:
DFREQUENCY:STATE?
-> :FFT1:MEASURE:MARKER:BASIC:DFREQUE
NCY:STATE 1
:FFT<x>:MEASure:MARKer[:BASic]:DFReq
uency:VALue?
Function Queries the frequency between marker cursors for
FFT analysis.
Syntax
:FFT<x>:MEASure:MARKer[:BASic]:DFRequ
ency:VALue?
<x> = 1 or 2 (1 only for 2-channel models)
Example
:FFT1:MEASURE:MARKER:BASIC:
DFREQUENCY:VALUE?
-> :FFT1:MEASURE:MARKER:BASIC:DFREQUE
NCY:VALUE 1.000E+00
:FFT<x>:MEASure:MARKer[:BASic]:DV?
Function Queries all of the settings for level measurement
between marker cursors for FFT analysis.
Syntax
:FFT<x>:MEASure:MARKer[:BASic]:DV?
<x> = 1 or 2 (1 only for 2-channel models)
:FFT<x>:MEASure:MARKer[:BASic]:DV:ST
ATe
Function Sets or queries the on/off status of the level
measured between marker cursors for FFT
analysis.
Syntax
:FFT<x>:MEASure:MARKer[:BASic]:DV:STA
Te {<Boolean>}
:FFT<x>:MEASure:MARKer[:BASic]:DV:STA
Te?
<x> = 1 or 2 (1 only for 2-channel models)
Example
:FFT1:MEASURE:MARKER:BASIC:DV:STA
TE ON
:FFT1:MEASURE:MARKER:BASIC:DV:STATE?
-> :FFT1:MEASURE:MARKER:BASIC:DV:STA
TE 1
:FFT<x>:MEASure:MARKer[:BASic]:DV:VA
Lue?
Function Queries the level between marker cursors for FFT
analysis.
Syntax
:FFT<x>:MEASure:MARKer[:BASic]:DV:VAL
ue?
<x> = 1 or 2 (1 only for 2-channel models)
Example
:FFT1:MEASURE:MARKER:BASIC:DV:VALUE?
-> :FFT1:MEASURE:MARKER:BASIC:DV:VAL
UE 1.000E+00
:FFT<x>:MEASure:MARKer[:BASic]:FREQu
ency<y>?
Function Queries all of the settings for frequency
measurement of a marker cursor for FFT analysis.
Syntax
:FFT<x>:MEASure:MARKer[:BASic]:FREQue
ncy<y>?
<x> = 1 or 2 (1 only for 2-channel models)
<y> = 1 or 2
5.11 FFT Group