YOKOGAWA DLM2000 Series - Page 208

5-175
IM 710105-17E
Commands
1
2
3
4
5
6
App
Index
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:INDIcator:STFRame
Function Sets or queries whether or not the indicator start
frame, which is one of the ID and data conditions,
for FLEXRAY bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:I
DData]:INDIcator:STFRame {0|1|X}
:SERialbus<x>:FLEXray:SEARch:SETup[:I
DData]:INDIcator:STFRame?
<x> = 1 to 4
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDDA
TA:INDICATOR:STFRAME 1
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDDA
TA:INDICATOR:STFRAME?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:I
DDATA:INDICATOR:STFRAME 1
:SERialbus<x>:FLEXray:SEARch:SETup[:
IDData]:INDIcator:SYFRame
Function Sets or queries the indicator sync frame, which is
one of the ID and data conditions, for FLEXRAY
bus signal searching.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup[:I
DData]:INDIcator:SYFRame {0|1|X}
:SERialbus<x>:FLEXray:SEARch:SETup[:I
DData]:INDIcator:SYFRame?
<x> = 1 to 4
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDDA
TA:INDICATOR:SYFRAME 1
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:IDDA
TA:INDICATOR:SYFRAME?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:I
DDATA:INDICATOR:SYFRAME 1
:SERialbus<x>:FLEXray:SEARch:SETup:M
ODE
Function Sets or queries the FLEXRAY bus signal search
mode.
Syntax
:SERialbus<x>:FLEXray:SEARch:SETup:MO
DE {ERRor|FSTart|IDData}
:SERialbus<x>:FLEXray:SEARch:SETup:MO
DE?
<x> = 1 to 4
Example
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:MO
DE FSTART
:SERIALBUS1:FLEXRAY:SEARCH:SETUP:MO
DE?
-> :SERIALBUS1:FLEXRAY:SEARCH:SETUP:M
ODE FSTART
:SERialbus<x>:I2C?
Function Queries all I
2
C bus signal analysis and search
settings.
Syntax
:SERialbus<x>:I2C?
<x> = 1 to 4
:SERialbus<x>:I2C[:ANALyze]?
Function Queries all I
2
C bus signal analysis settings.
Syntax
:SERialbus<x>:I2C[:ANALyze]?
<x> = 1 to 4
:SERialbus<x>:I2C[:ANALyze]:SETup?
Function Queries all I
2
C bus signal analysis bus settings.
Syntax
:SERialbus<x>:I2C[:ANALyze]:SETup?
<x> = 1 to 4
:SERialbus<x>:I2C[:ANALyze]:SETup:CL
OCk?
Function Queries all I
2
C bus signal analysis clock settings.
Syntax
:SERialbus<x>:I2C[:ANALyze]:SETup:CLO
Ck?
<x> = 1 to 4
:SERialbus<x>:I2C[:ANALyze]:SETup:CL
OCk:SOURce
Function Sets or queries the clock source for I
2
C bus signal
analysis.
Syntax
:SERialbus<x>:I2C[:ANALyze]:SETup:CLO
Ck:SOURce {<NRf>|BIT<x>|MATH<x>}
:SERialbus<x>:I2C[:ANALyze]:SETup:CLO
Ck:SOURce?
<x> = 1 to 4
<NRf> = 1 to 4
<x> of BIT<x> = 1 to 8
<x> of MATH<x> = 1 or 2
Example
:SERIALBUS1:I2C:ANALYZE:SETUP:CLOCK:S
OURCE 1
:SERIALBUS1:I2C:ANALYZE:SETUP:CLOCK:S
OURCE?
-> :SERIALBUS1:I2C:ANALYZE:SETUP:CLOC
K:SOURCE 1
:SERialbus<x>:I2C[:ANALyze]:SETup:DA
TA?
Function Queries all I
2
C bus signal analysis data settings.
Syntax
:SERialbus<x>:I2C[:ANALyze]:SETup:DA
TA?
<x> = 1 to 4
:SERialbus<x>:I2C[:ANALyze]:SETup:DA
TA:SOURce
Function Sets or queries the I
2
C bus signal data source.
Syntax
:SERialbus<x>:I2C[:ANALyze]:SETup:DAT
A:SOURce {<NRf>|BIT<x>|MATH<x>}
:SERialbus<x>:I2C[:ANALyze]:SETup:DAT
A:SOURce?
<x> = 1 to 4
<NRf>|BIT<x>|MATH<x> = 1 to 4
Example
:SERIALBUS1:I2C:ANALYZE:SETUP:DATA:SO
URCE 1
:SERIALBUS1:I2C:ANALYZE:SETUP:DATA:SO
URCE?
-> :SERIALBUS1:I2C:ANALYZE:SETUP:DATA
:SOURCE 1
5.24 SERialbus Group