YOKOGAWA DLM2000 Series - Page 209

5-176
IM 710105-17E
:SERialbus<x>:I2C:DETail?
Function Queries all I
2
C bus signal analysis result list
settings.
Syntax
:SERialbus<x>:I2C:DETail?
<x> = 1 to 4
:SERialbus<x>:I2C:DETail:DISPlay
Function Sets or queries the display mode for the I
2
C bus
signal analysis result list.
Syntax
:SERialbus<x>:I2C:DETail:DISPl
ay {FULL|LOWer|UPPer}
:SERialbus<x>:I2C:DETail:DISPlay?
<x> = 1 to 4
Example
:SERIALBUS1:I2C:DETAIL:DISPLAY FULL
:SERIALBUS1:I2C:DETAIL:DISPLAY?
-> :SERIALBUS1:I2C:DETAIL:DISPLAY FUL
L
:SERialbus<x>:I2C:DETail:LIST:ITEM?
Function Queries all items that will be displayed in the I
2
C
bus signal analysis result list.
Syntax
:SERialbus<x>:I2C:DETail:LIST:ITEM?
<x> = 1 to 4
Example
:SERIALBUS1:I2C:DETAIL:LIST:ITEM?
-> :SERIALBUS1:I2C:DETAIL:LIST:IT
EM "No.,Time(ms),1st,2nd,R/W,Data,
Information,"
:SERialbus<x>:I2C:DETail:LIST:VALue?
Function Queries all of the data for the specified analysis
number in the I
2
C bus signal analysis result list.
Syntax
:SERialbus<x>:I2C:DETail:LIST:VAL
ue? {<NRf>|MAXimum|MINimum}
<x> = 1 to 4
<NRf> = See the DLM2000 Features Guide for
this information.
Example
:SERIALBUS1:I2C:DETAIL:LIST:VALUE? 0
-> :SERIALBUS1:I2C:DETAIL:LIST:
VALUE"0,−0.07000,AA*,,W,AE*88*,7-
bit,"
:SERialbus<x>:I2C[:ANALyze]:SETup:IN
CLuderw
Function Sets or queries the on/off status of the R/W
address bit in I
2
C bus signal analysis.
Syntax
:SERialbus<x>:I2C[:ANALyze]:SETup:INC
Luderw {<Boolean>}
:SERialbus<x>:I2C[:ANALyze]:SETup:INC
Luderw?
<x> = 1 to 4
Example
:SERIALBUS1:I2C:ANALYZE:SETUP:INCLUDE
RW ON
:SERIALBUS1:I2C:ANALYZE:SETUP:INCLUDE
RW?
-> :SERIALBUS1:I2C:ANALYZE:SETUP:INCL
UDERW 1
:SERialbus<x>:I2C:SEARch?
Function Queries all I
2
C bus signal search settings.
Syntax
:SERialbus<x>:I2C:SEARch?
<x> = 1 to 4
:SERialbus<x>:I2C:SEARch:ABORt
Function Aborts the I
2
C bus signal search.
Syntax
:SERialbus<x>:I2C:SEARch:ABORt
<x> = 1 to 4
Example
:SERIALBUS1:I2C:SEARCH:ABORT
:SERialbus<x>:I2C:SEARch:EXECute
Function Executes a I
2
C bus signal search.
Syntax
:SERialbus<x>:I2C:SEARch:EXECute
<x> = 1 to 4
Example
:SERIALBUS1:I2C:SEARCH:EXECUTE
:SERialbus<x>:I2C:SEARch:SELect
Function Sets which detected point to display in the I
2
C bus
signal search zoom window and queries the zoom
position of the detected point.
Syntax
:SERialbus<x>:I2C:SEARch:SELect {<NRf
>|MAXimum}
:SERialbus<x>:I2C:SEARch:SELect?
<x> = 1 to 4
<NRf> = 0 to 49999
Example
:SERIALBUS1:I2C:SEARCH:SELECT 1
:SERIALBUS1:I2C:SEARCH:SELECT?
-> :SERIALBUS1:I2C:SEARCH:SELECT 1.50
0E+00
Description If there are no detected points, the DLM2000
returns “NAN.”
:SERialbus<x>:I2C:SEARch:SELect?
MAXimum
Function Queries the number of detected points in the I
2
C
bus signal search.
Syntax
:SERialbus<x>:I2C:SEARch:SELe
ct? {MAXimum}
<x> = 1 to 4
Example
:SERIALBUS1:I2C:SEARCH:SELECT? MAXIMU
M
-> :SERIALBUS1:I2C:SEARCH:SELECT 100
Description If there are no detected points, the DLM2000
returns “NAN.”
:SERialbus<x>:I2C:SEARch[:SETup]?
Function Queries all I
2
C bus signal search condition
settings.
Syntax
:SERialbus<x>:I2C:SEARch[:SETup]?
<x> = 1 to 4
5.24 SERialbus Group