YOKOGAWA DLM2000 Series - Page 217

5-184
IM 710105-17E
:SERialbus<x>:LIN:SEARch:SETup:ERRor
:FRAMing
Function Sets or queries the LIN bus signal search framing
error setting.
Syntax
:SERialbus<x>:LIN:SEARch:SETup:ERRor:
FRAMing {<Boolean>}
:SERialbus<x>:LIN:SEARch:SETup:ERRor:
FRAMing?
<x> = 1 to 4
Example
:SERIALBUS1:LIN:SEARCH:SETUP:ERROR:FR
AMING ON
:SERIALBUS1:LIN:SEARCH:SETUP:ERROR:FR
AMING?
-> :SERIALBUS1:LIN:SEARCH:SETUP:ERROR
:FRAMING 1
:SERialbus<x>:LIN:SEARch:SETup:ERRor
:PARity
Function Sets or queries the LIN bus signal search parity
error setting.
Syntax
:SERialbus<x>:LIN:SEARch:SETup:ERRor:
PARity {<Boolean>}
:SERialbus<x>:LIN:SEARch:SETup:ERRor:
PARity?
<x> = 1 to 4
Example
:SERIALBUS1:LIN:SEARCH:SETUP:ERROR:PA
RITY ON
:SERIALBUS1:LIN:SEARCH:SETUP:ERROR:PA
RITY?
-> :SERIALBUS1:LIN:SEARCH:SETUP:ERROR
:PARITY 1
:SERialbus<x>:LIN:SEARch:SETup:ERRor
:SYNCh
Function Sets or queries the LIN bus signal search synch
error setting.
Syntax
:SERialbus<x>:LIN:SEARch:SETup:ERRor:
SYNCh {<Boolean>}
:SERialbus<x>:LIN:SEARch:SETup:ERRor:
SYNCh?
<x> = 1 to 4
Example
:SERIALBUS1:LIN:SEARCH:SETUP:ERROR:SY
NCH ON
:SERIALBUS1:LIN:SEARCH:SETUP:ERROR:SY
NCH?
-> :SERIALBUS1:LIN:SEARCH:SETUP:ERROR
:SYNCH 1
:SERialbus<x>:LIN:SEARch:SETup:ERRor
:TIMeout
Function Sets or queries the LIN bus signal search timeout
error setting.
Syntax
:SERialbus<x>:LIN:SEARch:SETup:ERRor:
TIMeout {<Boolean>}
:SERialbus<x>:LIN:SEARch:SETup:ERRor:
TIMeout?
<x> = 1 to 4
Example
:SERIALBUS1:LIN:SEARCH:SETUP:ERROR:TI
MEOUT ON
:SERIALBUS1:LIN:SEARCH:SETUP:ERROR:TI
MEOUT?
-> :SERIALBUS1:LIN:SEARCH:SETUP:ERROR
:TIMEOUT 1
:SERialbus<x>:LIN:SEARch:SETup:IDDa
ta?
Function Queries all ID and data condition settings for LIN
bus signal searching.
Syntax
:SERialbus<x>:LIN:SEARch:SETup:IDDa
ta?
<x> = 1 to 4
:SERialbus<x>:LIN:SEARch:SETup:IDDat
a:DATA?
Function Queries all LIN bus signal search data settings.
Syntax
:SERialbus<x>:LIN:SEARch:SETup:IDData
:DATA?
<x> = 1 to 4
:SERialbus<x>:LIN:SEARch:SETup:IDDat
a:DATA:CONDition
Function Sets or queries the data conditions for LIN bus
signal searching.
Syntax
:SERialbus<x>:LIN:SEARch:SETup:
IDData:DATA:CONDition {BETWeen|EQUal|
FALSe|GREater|LESS|NOTBetween|NOTEqul
|TRUE}
:SERialbus<x>:LIN:SEARch:SETup:
IDData:DATA:CONDition?
<x> = 1 to 4
Example
:SERIALBUS1:LIN:SEARCH:SETUP:IDDATA:D
ATA:CONDITION BETWEEN
:SERIALBUS1:LIN:SEARCH:SETUP:IDDATA:D
ATA:CONDITION?
-> :SERIALBUS1:LIN:SEARCH:SETUP:IDDAT
A:DATA:CONDITION BETWEEN
5.24 SERialbus Group