YOKOGAWA DLM2000 Series - Page 243

5-210
IM 710105-17E
:SERialbus<x>:SPATtern[:ANALyze]:SET
up?
Function Queries all user-defined bus signal analysis
settings.
Syntax
:SERialbus<x>:SPATtern[:ANALyze]:SET
up?
<x> = 1 to 4 (1 only for 2-channel models)
:SERialbus<x>:SPATtern[:ANALyze]:SET
up:BRATe
Function Sets or queries the bit rate for user-defined bus
signal analysis.
Syntax
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:BRATe {<NRf>}
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:BRATe?
<x> = 1 to 4 (1 only for 2-channel models)
<NRf> = 1000 to 50000000 (bps)
Example
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:BR
ATE 1000
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:BR
ATE?
-> :SERIALBUS1:SPATTERN:ANALYZE:
SETUP:BRATE 1000
:SERialbus<x>:SPATtern[:ANALyze]:SET
up:CLOCk?
Function Queries all clock signal settings for user-defined
bus signal analysis.
Syntax
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:CLOCk?
<x> = 1 to 4 (1 only for 2-channel models)
:SERialbus<x>:SPATtern[:ANALyze]:SET
up:CLOCk:MODE
Function Sets or queries the clock signal enable or disable
status for user-defined bus signal analysis.
Syntax
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:CLOCk:MODE {<Boolean>}
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:CLOCk:MODE?
<x> = 1 to 4 (1 only for 2-channel models)
Example
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:CL
OCK:MODE ON
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:CL
OCK:MODE?
-> :SERIALBUS1:SPATTERN:ANALYZE:SETUP
:CLOCK:MODE 1
:SERialbus<x>:SPATtern[:ANALyze]:SET
up:CLOCk:POLarity
Function Sets or queries the clock signal slope for user-
defined bus signal analysis.
Syntax
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:CLOCk:POLarity {FALL|RISE}
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:CLOCk:POLarity?
<x> = 1 to 4 (1 only for 2-channel models)
Example
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:CL
OCK:POLARITY FALL
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:CL
OCK:POLARITY?
-> :SERIALBUS1:SPATTERN:ANALYZE:SETUP
:CLOCK:POLARITY FALL
:SERialbus<x>:SPATtern[:ANALyze]:SET
up:CLOCk:SOURce
Function Sets or queries the clock signal for user-defined
bus signal analysis.
Syntax
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:CLOCk:SOURce {<NRf>}
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:CLOCk:SOURce?
<x> = 1 to 4 (1 only for 2-channel models)
<NRf> = 1 to 4 (1 or 2 for 2-channel models)
Example
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:CL
OCK:SOURCE 1
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:CL
OCK:SOURCE?
-> :SERIALBUS1:SPATTERN:ANALYZE:SETUP
:CLOCK:SOURCE 1
:SERialbus<x>:SPATtern[:ANALyze]:SET
up:CS?
Function Queries all chip select signal settings for user-
defined bus signal analysis.
Syntax
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:CS?
<x> = 1 to 4 (1 only for 2-channel models)
:SERialbus<x>:SPATtern[:ANALyze]:SET
up:CS:ACTive
Function Sets or queries the chip select signal active state
for user-defined bus signal analysis.
Syntax
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:CS:ACTive {HIGH|LOW}
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:CS:ACTive?
<x> = 1 to 4 (1 only for 2-channel models)
Example
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:
CS:ACTIVE HIGH
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:
CS:ACTIVE?
-> :SERIALBUS1:SPATTERN:ANALYZE:
SETUP:CS:ACTIVE HIGH
5.24 SERialbus Group