YOKOGAWA DLM2000 Series - Page 244

5-211
IM 710105-17E
Commands
1
2
3
4
5
6
App
Index
:SERialbus<x>:SPATtern[:ANALyze]:SET
up:CS:SOURce
Function Sets or queries the chip select signal for user-
defined bus signal analysis.
Syntax
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:CS:SOURce {<NRf>|NONE}
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:CS:SOURce?
<x> = 1 to 4 (1 only for 2-channel models)
<NRf> = 1 to 4 (NRf not available for 2-channel
models)
Example
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:
CS:SOURCE 1
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:
CS:SOURCE?
-> :SERIALBUS1:SPATTERN:ANALYZE:
SETUP:CS:SOURCE 1
:SERialbus<x>:SPATtern[:ANALyze]:SET
up:DATA?
Function Queries all data signal settings for user-defined
bus signal analysis.
Syntax
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:DATA?
<x> = 1 to 4 (1 only for 2-channel models)
:SERialbus<x>:SPATtern[:ANALyze]:SET
up:DATA:ACTive
Function Sets or queries the data signal active state for
user-defined bus signal analysis.
Syntax
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:DATA:ACTive {HIGH|LOW}
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:DATA:ACTive?
<x> = 1 to 4 (1 only for 2-channel models)
Example
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:DA
TA:ACTIVE HIGH
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:DA
TA:ACTIVE?
-> :SERIALBUS1:SPATTERN:ANALYZE:SETUP
:DATA:ACTIVE HIGH
:SERialbus<x>:SPATtern[:ANALyze]:SET
up:DATA:SOURce
Function Sets or queries the data signal for user-defined
bus signal analysis.
Syntax
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:DATA:SOURce {<NRf>}
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:DATA:SOURce?
<x> = 1 to 4 (1 only for 2-channel models)
<NRf> = 1 to 4 (1 or 2 for 2-channel models)
Example
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:DA
TA:SOURCE 1
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:DA
TA:SOURCE?
-> :SERIALBUS1:SPATTERN:ANALYZE:
SETUP:DATA:SOURCE 1
:SERialbus<x>:SPATtern[:ANALyze]:SET
up:LATCh?
Function Queries all latch signal settings for user-defined
bus signal analysis.
Syntax
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:LATCh?
<x> = 1 to 4 (1 only for 2-channel models)
:SERialbus<x>:SPATtern[:ANALyze]:SET
up:LATCh:POLarity
Function Sets or queries the latch signal slope for user-
defined bus signal analysis.
Syntax
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:LATCh:POLarity {FALL|RISE}
:SERialbus<x>:SPATtern[:ANALyze]:SETu
p:LATCh:POLarity?
<x> = 1 to 4 (1 only for 2-channel models)
Example
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:LA
TCH:POLARITY FALL
:SERIALBUS1:SPATTERN:ANALYZE:SETUP:LA
TCH:POLARITY?
-> :SERIALBUS1:SPATTERN:ANALYZE:
SETUP:LATCH:POLARITY FALL
5.24 SERialbus Group