5-65
IM 710105-17E
Commands
5
:ANALysis:PANalyze<x>:SOA:MODE
Function Sets or queries the automated measurement
mode of the XY display (safe operating area).
Syntax
:ANALysis:PANalyze<x>:SOA:MODE {CURSo
r|OFF}
:ANALysis:PANalyze<x>:SOA:MODE?
<x> = 1 or 2
Example :ANALYSIS:PANALYZE1:SOA:MODE CURSOR
:ANALYSIS:PANALYZE1:SOA:MODE?
-> :ANALYSIS:PANALYZE1:SOA:MODE CURSO
R
:ANALysis:PANalyze<x>:SOA:TRANge
(Time Range)
Function Sets or queries the range of the T-Y waveform to
display in the XY display (safe operating area).
Syntax
:ANALysis:PANalyze<x>:SOA:TRAN
ge {<NRf>,<NRf>}
:ANALysis:PANalyze<x>:SOA:TRANge?
<x> = 1 or 2
<NRf>=−5to5divisions(instepsof10divisions/
display record length)
Example
:ANALYSIS:PANALYZE1:SOA:TRANGE−4,4
:ANALYSIS:PANALYZE1:SOA:TRANGE?
->:ANALYSIS:PANALYZE1:SOA:TRANGE−4.
00,4.00
:ANALysis:PANalyze<x>:SOA:VTDisplay
Function Sets or queries whether or not to display the VT
waveform in the XY display (safe operating area).
Syntax
:ANALysis:PANalyze<x>:SOA:VTDispl
ay {<Boolean>}
:ANALysis:PANalyze<x>:SOA:VTDisplay?
<x> = 1 or 2
Example
:ANALYSIS:PANALYZE1:SOA:VTDISPLAY ON
:ANALYSIS:PANALYZE1:SOA:VTDISPLAY?
-> :ANALYSIS:PANALYZE1:SOA:
VTDISPLAY 1
:ANALysis:PANalyze<x>:SWLoss?
Function Queries all switching loss settings.
Syntax
:ANALysis:PANalyze<x>:SWLoss?
<x> = 1 or 2
Description Use the commands listed below to set the
reference levels (distal, mesial, proximal, etc.)
used to determine the total loss.
:MEASure:{CHANnel<x>|MATH<x>}:DPRoxim
al?
:MEASure:{CHANnel<x>|MATH<x>}:DPRoxim
al:MODE
:MEASure:{CHANnel<x>|MATH<x>}:DPRoxim
al:PERCent
:MEASure:{CHANnel<x>|MATH<x>}:DPRoxim
al:UNIT
:MEASure:{CHANnel<x>|MATH<x>}:METHod
:ANALysis:PANalyze<x>:SWLoss:CYCLe
Function Sets or queries the on/off status of cycle mode.
Syntax
:ANALysis:PANalyze<x>:SWLoss:CYC
Le {<Boolean>}
:ANALysis:PANalyze<x>:SWLoss:CYCLe?
<x> = 1 or 2
Example
:ANALYSIS:PANALYZE1:SWLOSS:CYCLE ON
:ANALYSIS:PANALYZE1:SWLOSS:CYCLE?
-> :ANALYSIS:PANALYZE1:SWLOSS:CYCLE 1
:ANALysis:PANalyze<x>:SWLoss:DPROxim
al?
Function Queries all distal, mesial, and proximal settings.
Syntax
:ANALysis:PANalyze<x>:SWLoss:DPROxim
al?
<x> = 1 or 2
Example
:ANALYSIS:PANALYZE1:SWLOSS:DPROXIMAL?
:ANALysis:PANalyze<x>:SWLoss:DPROxim
al:MODE
Function Sets or queries the distal, mesial, and proximal
point mode setting.
Syntax
:ANALysis:PANalyze<x>:SWLoss:DPROxima
l:MODE {PERCent|UNIT}
:ANALysis:PANalyze<x>:SWLoss:DPROxima
l:MODE?
<x> = 1 or 2
Example
:ANALYSIS:PANALYZE1:SWLOSS:DPROXIMAL:
MODE PERCENT
:ANALYSIS:PANALYZE1:SWLOSS:DPROXIMAL:
MODE?
-> :ANALYSIS:PANALYZE1:SWLOSS:DPROXIM
AL:MODE PERCENT
5.3 ANALysis Group
To Next Page
Loading...
Need help?
General
