YOKOGAWA DLM4038 - Page 133

5-100
IM DLM4038-17EN
:FFT<x>:MEASure:MARKer[:BASic]:V<y>:
VALue?
Function Queries the level of a marker cursor for FFT
analysis.
Syntax
:FFT<x>:MEASure:MARKer[:BASic]:V<y>:
VALue?
<x> = 1 to 2
<y> = 1 to 2
Example
:FFT1:MEASURE:MARKER:BASIC:V1:VALUE?
-> :FFT1:MEASURE:MARKER:BASIC:V1:VAL
UE 1.000E+00
:FFT<x>:MEASure:MODE
Function Sets or queries the FFT analysis automatic
measurement mode.
Syntax
:FFT<x>:MEASure:MODE {MARKer|OFF|PEA
K}
:FFT<x>:MEASure:MODE?
<x> = 1 to 2
Example
:FFT1:MEASURE:MODE MARKER
:FFT1:MEASURE:MODE?
-> :FFT1:MEASURE:MODE MARKER
:FFT<x>:MEASure:PEAK?
Function Queries all peak measurement settings for FFT
analysis.
Syntax
:FFT<x>:MEASure:PEAK?
<x> = 1 to 2
:FFT<x>:MEASure:PEAK[:BASic]?
Function Queries all Basic peak item settings for FFT
analysis.
Syntax
:FFT<x>:MEASure:PEAK[:BASic]?
<x> = 1 to 2
:FFT<x>:MEASure:PEAK[:BASic]:ALL
Function Collectively turns on or off all Basic peak items
for FFT analysis.
Syntax
:FFT<x>:MEASure:PEAK[:BASic]:A
LL {<Boolean>}
<x> = 1 to 2
Example
:FFT1:MEASURE:PEAK:BASIC:ALL ON
:FFT<x>:MEASure:PEAK[:BASic]:DFReque
ncy?
Function Queries all of the settings for frequency
measurement between peak values for FFT
analysis.
Syntax
:FFT<x>:MEASure:PEAK[:BASic]:DFReque
ncy?
<x> = 1 to 2
:FFT<x>:MEASure:MARKer[:BASic]:FREQu
ency<y>:VALue?
Function Queries the frequency of a marker cursor for FFT
analysis.
Syntax
:FFT<x>:MEASure:MARKer[:BASic]:FREQu
ency<y>:VALue?
<x> = 1 to 2
<y> = 1 to 2
Example
:FFT1:MEASURE:MARKER:BASIC:FREQUENCY
1:VALUE?
-> :FFT1:MEASURE:MARKER:BASIC:FREQUE
NCY1:VALUE 1.000E+00
:FFT<x>:MEASure:MARKer[:BASic]:POSit
ion<y>
Function Sets or queries the position of a marker cursor for
FFT analysis.
Syntax
:FFT<x>:MEASure:MARKer[:BASic]:POSit
ion<y> {<NRf>}
:FFT<x>:MEASure:MARKer[:BASic]:POSit
ion<y>?
<x> = 1 to 2
<y> = 1 to 2
<NRf> = −5 to 5 (divisions)
Example
:FFT1:MEASURE:MARKER:BASIC:POSITI
ON1 1
:FFT1:MEASURE:MARKER:BASIC:POSITI
ON1?
-> :FFT1:MEASURE:MARKER:BASIC:POSITI
ON1 1.000E+00
:FFT<x>:MEASure:MARKer[:BASic]:V<y>?
Function Queries all of the settings for level measurement
of a marker cursor for FFT analysis.
Syntax
:FFT<x>:MEASure:MARKer[:BASic]:V<y>?
<x> = 1 to 2
<y> = 1 to 2
:FFT<x>:MEASure:MARKer[:BASic]:V<y>:
STATe
Function Sets or queries the on/off status of the level of
marker cursor for FFT analysis.
Syntax
:FFT<x>:MEASure:MARKer[:BASic]:V<y>:
STATe {<Boolean>}
:FFT<x>:MEASure:MARKer[:BASic]:V<y>:
STATe?
<x> = 1 to 2
<y> = 1 to 2
Example
:FFT1:MEASURE:MARKER:BASIC:V1:STA
TE ON
:FFT1:MEASURE:MARKER:BASIC:V1:STATE?
-> :FFT1:MEASURE:MARKER:BASIC:V1:STA
TE 1
5.12 FFT Group