YOKOGAWA DLM4038 - Page 209

5-176
IM DLM4038-17EN
:SERialbus<x>:CXPI:SEARch:SETup[:IDD
ata]:DATA:CONDition
Function Sets or queries the comparison condition, which
is one of the ID and data conditions, for CXPI bus
signal searching.
Syntax
:SERialbus<x>:CXPI:SEARch:
SETup[:IDData]:DATA:
CONDition {BETWeen|EQUal|FALSe|
GREater|LESS|NOTBetween|NOTEqul|
TRUE}
:SERialbus<x>:CXPI:SEARch:
SETup[:IDData]:DATA:CONDition?
<x> = 1 to 4
Example
:SERIALBUS1:CXPI:SEARCH:SETUP:
IDDATA:DATA:CONDITION BETWEEN
:SERIALBUS1:CXPI:SEARCH:SETUP:
IDDATA:DATA:CONDITION?
-> :SERIALBUS1:CXPI:SEARCH:SETUP:
IDDATA:DATA:CONDITION BETWEEN
:SERialbus<x>:CXPI:SEARch:SETup[:IDD
ata]:DATA:DBYTe
Function Sets or queries the number of data bytes, which
is one of the ID and data conditions, for CXPI bus
signal searching.
Syntax
:SERialbus<x>:CXPI:SEARch:
SETup[:IDData]:DATA:DBYTe {<NRf>}
:SERialbus<x>:CXPI:SEARch:
SETup[:IDData]:DATA:DBYTe?
<x> = 1 to 4
<NRf> = 0 to 8
Example
:SERIALBUS1:CXPI:SEARCH:SETUP:
IDDATA:DATA:DBYTE 1
:SERIALBUS1:CXPI:SEARCH:SETUP:
IDDATA:DATA:DBYTE?
-> :SERIALBUS1:CXPI:SEARCH:SETUP:
IDDATA:DATA:DBYTE 1
:SERialbus<x>:CXPI:SEARch:SETup[:IDD
ata]:DATA:DECimal<y>
Function Sets a reference value, which is one of the ID and
data conditions, for CXPI bus signal searching in
decimal notation.
Syntax
:SERialbus<x>:CXPI:SEARch:
SETup[:IDData]:DATA:
DECimal<y> {<NRf>}
:SERialbus<x>:CXPI:SEARch:
SETup[:IDData]:DATA:DECimal<y>?
<x> = 1 to 4
<y> = 1, 2
<NRf> = –9E+18 to 9E+18
Example
:SERIALBUS1:CXPI:SEARCH:SETUP:
IDDATA:DATA:DECIMAL1 1
:SERIALBUS1:CXPI:SEARCH:SETUP:
IDDATA:DATA:DECIMAL1?
-> :SERIALBUS1:CXPI:SEARCH:SETUP:
IDDATA:DATA:DECIMAL1 1.0000000E+00
:SERialbus<x>:CXPI:SEARch:SETup[:IDD
ata]:DATA:ENDian
Function Sets or queries the byte order of the reference
values, which is one of the ID and data
conditions, for CXPI bus signal searching.
Syntax
:SERialbus<x>:CXPI:SEARch:
SETup[:IDData]:DATA:
ENDian {BIG|LITTle}
:SERialbus<x>:CXPI:SEARch:
SETup[:IDData]:DATA:ENDian?
<x> = 1 to 4
Example
:SERIALBUS1:CXPI:SEARCH:SETUP:
IDDATA:DATA:ENDIAN BIG
:SERIALBUS1:CXPI:SEARCH:SETUP:
IDDATA:DATA:ENDIAN?
-> :SERIALBUS1:CXPI:SEARCH:SETUP:
IDDATA:DATA:ENDIAN BIG
:SERialbus<x>:CXPI:SEARch:SETup[:IDD
ata]:DATA:HEXa<y>
Function Sets a reference value, which is one of the ID and
data conditions, for CXPI bus signal searching in
hexadecimal notation.
Syntax
:SERialbus<x>:CXPI:SEARch:
SETup[:IDData]:DATA:
HEXa<y> {<String>}
:SERialbus<x>:CXPI:SEARch:
SETup[:IDData]:DATA:HEXa<y>?
<x> = 1 to 4
<y> = 1 to 8
Example
:SERIALBUS1:CXPI:SEARCH:SETUP:
IDDATA:DATA:HEXA1 “12”
:SERialbus<x>:CXPI:SEARch:SETup[:IDD
ata]:DATA:MODE
Function Sets or queries the ID and data condition
(enabled/disabled) for CXPI bus signal searching.
Syntax
:SERialbus<x>:CXPI:SEARch:
SETup[:IDData]:DATA:MODE {<Boolean>}
:SERialbus<x>:CXPI:SEARch:
SETup[:IDData]:DATA:MODE?
<x> = 1 to 4
Example
:SERIALBUS1:CXPI:SEARCH:SETUP:
IDDATA:DATA:MODE ON
:SERIALBUS1:CXPI:SEARCH:SETUP:
IDDATA:DATA:MODE?
-> :SERIALBUS1:CXPI:SEARCH:SETUP:
IDDATA:DATA:MODE 1
5.25 SERialbus Group