YOKOGAWA DLM4038 - Page 224

5-191
IM DLM4038-17EN
Commands
1
2
3
4
5
6
App
Index
:SERialbus<x>:I2C:SEARch[:SETup]:ADD
Ress:ADDRess:BIT7APsub:SADDress:HEXa
Function Sets the sub address for the 7-bit + sub address
for I
2
C bus signal searching in hexadecimal
notation.
Syntax
:SERialbus<x>:I2C:SEARch[:SETup]:AD
DRess:ADDRess:BIT7APsub:SADDress:HE
Xa {<String>}
<x> = 1 to 4
Example
:SERIALBUS1:I2C:SEARCH:SETUP:ADDR
ESS:ADDRESS:BIT7APSUB:SADDRESS:HE
XA "EF"
:SERialbus<x>:I2C:SEARch[:SETup]:ADD
Ress:ADDRess:BIT7APsub:SADDress:PATT
ern
Function Sets or queries the sub address for the 7-bit +
sub address for I
2
C bus signal searching in binary
notation.
Syntax
:SERialbus<x>:I2C:SEARch[:SETup]:ADD
Ress:ADDRess:BIT7APsub:SADDress:PATT
ern {<String>}
:SERialbus<x>:I2C:SEARch[:SETup]:ADD
Ress:ADDRess:BIT7APsub:SADDress:PATT
ern?
<x> = 1 to 4
Example
:SERIALBUS1:I2C:SEARCH:SETUP:ADDRE
SS:
ADDRESS:BIT7APSUB:SADDRESS:PATTE
RN "00111010"
:SERIALBUS1:I2C:SEARCH:SETUP:ADDRESS
:ADDRESS:BIT7APSUB:SADDRESS:PATTERN?
-> :SERIALBUS1:I2C:SEARCH:SETUP:ADDR
ESS:ADDRESS:BIT7APSUB:SADDRESS:PATTE
RN "00111010"
:SERialbus<x>:I2C:SEARch[:SETup]:ADD
Ress:ADDRess:MODE
Function Sets or queries the address condition enable/
disable mode for I
2
C bus signal searching.
Syntax
:SERialbus<x>:I2C:SEARch[:SETup]:ADD
Ress:ADDRess:MODE {<Boolean>}
:SERialbus<x>:I2C:SEARch[:SETup]:ADD
Ress:ADDRess:MODE?
<x> = 1 to 4
Example
:SERIALBUS1:I2C:SEARCH:SETUP:ADDRESS
:ADDRESS:MODE ON
:SERIALBUS1:I2C:SEARCH:SETUP:ADDRESS
:ADDRESS:MODE?
-> :SERIALBUS1:I2C:SEARCH:SETUP:ADDR
ESS:ADDRESS:MODE 1
:SERialbus<x>:I2C:SEARch[:SETup]:ADD
Ress:ADDRess:PFORmat
Function Sets or queries the address input format, which is
one of the address conditions, for I
2
C bus signal
searching.
Syntax
:SERialbus<x>:I2C:SEARch[:SETup]:ADD
Ress:ADDRess:PFORmat {BINary|HEXa}
:SERialbus<x>:I2C:SEARch[:SETup]:ADD
Ress:ADDRess:PFORmat?
<x> = 1 to 4
Example
:SERIALBUS1:I2C:SEARCH:SETUP:ADDRESS
:ADDRESS:PFORMAT BINARY
:SERIALBUS1:I2C:SEARCH:SETUP:ADDRESS
:ADDRESS:PFORMAT?
-> :SERIALBUS1:I2C:SEARCH:SETUP:ADDR
ESS:ADDRESS:PFORMAT BINARY
:SERialbus<x>:I2C:SEARch[:SETup]:ADD
Ress:ADDRess:TYPE
Function Sets or queries the address type, which is one
of the address conditions, for I
2
C bus signal
searching.
Syntax
:SERialbus<x>:I2C:SEARch[:SETup]:ADD
Ress:ADDRess:TYPE {BIT10ADdress|BIT7
ADdress|BIT7APsub}
:SERialbus<x>:I2C:SEARch[:SETup]:ADD
Ress:ADDRess:TYPE?
<x> = 1 to 4
Example
:SERIALBUS1:I2C:SEARCH:SETUP:ADDRESS
:ADDRESS:TYPE BIT10ADDRESS
:SERIALBUS1:I2C:SEARCH:SETUP:ADDRESS
:ADDRESS:TYPE?
-> :SERIALBUS1:I2C:SEARCH:SETUP:ADDR
ESS:ADDRESS:TYPE BIT10ADDRESS
:SERialbus<x>:I2C:SEARch[:SETup]:ADD
Ress:DATA?
Function Queries all address pattern data settings for I
2
C
bus signal searching.
Syntax
:SERialbus<x>:I2C:SEARch[:SETup]:ADD
Ress:DATA?
<x> = 1 to 4
5.25 SERialbus Group